Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
We have a wired Aironet 1130AG which we cannot connect to. We got a cable to hook it up to a computer with the Hyperterminal. But we don't know the commands to connect to it. Can anyone give us some advice?ThanksMike
helloi have WiFi network build on AIR-AP1121G-E-K9(6 AP), and CIS-WS-CE500-24LC.in this moment, its just one WiFi network with WPA2 security. q: can i build multiple WLANs on this AP?
i am deploying (1) 1242ag as root-bridge with multiple vlans and ssids but have left the key the same for each ssid/vlan. the remote (4) 1242ag's will be configured as work-group bridges with 1 vlan & 1 ssid for each. The key will be the same on all ...
A wireless bridged site is intermittantly losing voice and data connectivity between the Aironet 1310 bridge and the switch at that location. The wireless connection between buildings is always on. When doing the show CDP neighbor command on the remo...
Resolved! AP 1310 - distance from Power injector
I need to place my 1300 antenna some distance away from the power injector.Is there a distance limitation on the 2 coax cables connecting the antenna to the power injector?
I am having an issue with my 4402. In the WLAN I have created there is a setting called Session Timeout. This by default is set to 1800 secs. This forces the clients to reauthenticate on the wireless every 30 minutes. I want to change this to 28000 s...
Hi,what is the highest secuirty that we can provide to the wireless phones which are communication with VOICE SSID.pl help me with configuration for Autonomous AP's.
Resolved! MLPP with LWAPP deployement
Hi,I would like to know if you LWAPP APs can handle MLPP. My feeling is that is not possible since MLPP use RSVP on each node on the path and since QoS in LWAPP mode is propagated via LWAPP tunnels. Am I right? For example I want to deploy Aironet 15...
Hi All,I have been running a WiSM successfully for months now, but our wireless network has grown quite a bit so we have purchased a second WiSM. Are there any best practises for implementing another one, or are there any design guides?Thanks,Michael
I am using Cisco AP1121G access points with Cisco PI21AG cards(and ACU) running WPA2 with LEAP authentication against an ACS server. The problem is that the clients experience a constant slowdown. When a client is started, it will run fine for a coup...
Resolved! the use of RRM ?
we did an site survey for a warehouse in witch we had 20 ap's (1050) foreseen, we made a channel map with power adjustments, once the installation was complete we enabled the RRM feature on the controller, this feature should fine tune the rf enviore...
I understand the Cipher TKIP is the most secure encryption for a point-to-point bridge. I have enabled Cipher TKIP on both sides, but do I need to enter a n encryption key? If I do where do I enter the key at? Also is there a sample basic config for...
I have an out of service AP 1131. I have a replacement ready to install but I'm concerned w/ the map on the WCS. How can I go about replacing the existing AP w/ the new AP while using the existing name?Robert MaldonadoSr. Systems Administrator
Hello,concerning the floor maps of a building: is it possible to show the coverage caused by an AP which is on a floor below or above?Thanks for any advice, p.k.
Hi,The goal of our application is a data transmission network between the ground infrastructure and vehicles. On the ground, we planned to use LWAPP AP1242 managed by a WLC. On board, we planed to use a MAR3200, fitted with 2 WMIC. In a first time, w...
