Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi, We have concerns about the use of an SSID dedicated to production, on which are Raspberry pi connected in 2. 4GHz.Users use Raspberry pi to connect to remote desktops, and the slightest disconnection cuts off the session, which sometimes happens ...
Dear All, I would like to ask how i can add my Catalyst 9200 switch into meraki dashboard ? does it needs a dnac license in order to do that ? Best Regards, Keith
Hi Folks,I try to find Meraki AP with frame rate of 2.7 Gbps*, with up to 2,402 Mbps in the 2.4 GHz (roughly) band and 287 Mbps* in the 5 GHz (roughly)For MR44 and based on the datasheet it supports: “frame rate of 2.7 Gbps*, with up to 2,402 Mbps in...
Hello we have trouble with access point C9120AXI-E when they are connected on "c9200L PoE+" ports.WLC 9800: IOS Version 17.9.3 (VID 5 and 7)C9200L Poe+: IOS Version 17.9.3 Cupertino (same issues with 17.11.01)In the access point guide, i've find the ...
how many users can connect in one access point with how many meters coverage with omni directionmodel # Cisco 9166I
Hi all,I currently configure wlc9800 with 4 ssid on it. In one of the wlan I use radius server for domain users to authenticate but I need to restrict them to connect only with their workstation laptops or tablets. I have all wlan MAC addresses avail...
Hi,I currently moved from Meraki to WLC9800 controller. after setting everything and joining AP to my site the ssid are not broadcasting and radios shows down status. because i am new to this controller need an urgent help.
I am trying to Upgrade code on Cisco APs by moving the AP to a New Controller with Newer Code. This process is taking three hours per AP. I have hundreds of APs. Is this a known issue? Cisco suggests upgrading via console port on each ap, but tha...
First time, trying to use the Meraki Enterprise Sandbox.-Thinking I should see:MX-84, MS225-24P switch, one MR53AP and one MV12 Camera-Instead:"Relevant Resources were not found."Is this broken, or am I missing something? Thank you.
Hello,I have a remote site that has a lot of users that connect their mobile phones to wifi and eventually exhaust my DHCP scope. I want to block these devices from connecting at all. I have used the block policy, however, these devices still connect...
Hello! I need to block one device on my Wireless Lan. I mean, I need this device not connect to my SSID. Can I do this? Can I to block the mac-address of this device? Thank you!
Hello AP9115 I have a question while setting up. SSID configuration completed and checked ping to AP-> Radius server However, the connection does not persist in the AP and clicking SSID does not connect or disconnects after attempting. The log ...
My accest point seri 9115AXE-FAP Name : AP6871.619E.C948Admin State : EnabledAP Mode : LocalAP Submode : Not ConfiguredLocation : default locationPrimary controller name : Secondary controller name :Tertiary controller name :AP join priority : 1IP Pr...
Hi Team,Can you pls help to understand how important is FT with WPA3-Enterprise , i know AES (CCMP) works with FT enable but GCMP does not support FT as per Cisco documents for WPA3 deployment. my questions are below ? currently my WLC IOS is 17.9.31...
How do i convert a CW9164-MR to be managed by Cisco WLC & DNAC?
