Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Have installed a Verisign class 3 certificate on ACS 3.3 in order to provide Peap authentication on Wireless client. If we view the certificate when the Wireless client authenticate to ACS, it show the Verisign Intermediate certificate has expired (0...
I try to upgrade a WS-SVC-WISM-1-K9 from 3.2.116.21 to 4.0.155.0 (SWISMK9-4-0-155-0.aes)which fail with this error:Tue Jun 13 14:36:41 2006: tftp rc=0, pHost=1.2.3.4 pFilename=wifi/SWISMK9-4-0-155-0.aes pLocalFilename=/mnt/download/local.tgzTue J...
We have a number of AP350s which we're upgrading from VxWorks to IOS. The conversion to IOS works fine but when I try and upgrade to a later version of IOS frequently the dot11radio0 interface disappears after the upgrade. On one AP the interface cam...
I have two root bridges - A & B - and I have one non root bridge - Z. The bridges A & B are broadcasting the same SSIDs and so Z can associate to either of them. The directional antennas, line of sight and everything has been set so that Z would obvi...
If I currently have an 802.11g network that has been optimized to support data devices at 36 Mb/s or higher (i.e., AP cells a little closer to maintain higher speeds) and I now want to add 7920 wireless phone support, do I have to re-do my site surve...
I am not sure if this is the correct place to ask the following questions, but here it goes...As part of a wireless pilot project we have installed 50 access points (Cisco aironet 1231G) in a couple of buildings. The real project once approved could ...
I am setting a wireless interconnection. In the Head Office I have a Cisco 1310 root Bridge and in the remote office I have the Cisco 1310 acting as the bridge. My question is - Could I directly connect the Cisco Access Point to the Cisco Aironet Po...
Hi,We have to implement wireless lan with WRT5RG devices.We have the reason to use only this model.Our question is how much area one accesspoint can cover. Based on that we will decide how many access points we have to purchase?Regardsskrao
AP boots fine on ac power but drops power entirely upon connecting ethernet cable.
I have an aironet 1100 configured as the root and I want the aironet 350 as the repeater. After all is setup I keep receiving authentication failed messages on the log of the 1100. any thoughts?
Resolved! Aironet 1200 and MAC Authentication
Hi All,I have got Aironet 1210 and want to implement MAC Authentication without ACS.Now, I know that any Aironet AP can allow MAC-Authentication by itself storing all the MAC Address List.Hence after the command:TestAP(config-if-ssid)#authentication ...
I have setup a lwapp system with about 6 AP's. Everything works great but on one of the WLAN's I have Web Authentication setup. For some reason, I cannot get this to work. I have tried every setting possible, played with the virtual interface but I c...
I tested windows XP SP2 client PEAP machine authentication with ACS server. The ACS uses self signed certificate. I have to uncheck "Validate server certificate", otherwise machine authenticaion does not work even I have imported the ACS self signed ...
When do you enable the ethernet multicast mode on controller? In my test lab, I have it disabled and I have not seen any issues so far. Thanks.
At the informational link below - we are informed that when using LAN interfaces for failover link you must go through a switch and not use a cross-over cable between the two pixes in the pair. It does not however explain why this is the case. Does...
