Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
We have a few pairs of 9800-80 and approx 13k APs. We would like to start using the AAA local Device Authentication for AP join, but since we use redundancy between the HA pairs we need to identify the capacity and the load that this new service woul...
I'm curious whether it is possible to configure virtual IP to be able to monitor active WLC from HA pair via SNMP. So let's assume I have HA configured for 2 WLCs: WLC1 and WLC2. I want to configure virtual IP to monitor always active WLC from this p...
Hello Team, This is my first engagement in Outdoor Wireless Design / Troubleshooting. We have a Client who is having issues in Outdoor Wireless . They are located near the Airport / Establishments so they are getting continuous radar hits on their ou...
Hello ,I'm trying to send a test BTM request to client using test wireless 11v command. But it doesnt add/delete any neighbor as per command.cisco 9800 + 9120 AXEtest wireless dot11v btmreq prepare 18f9.3565.4980 1 9test wireless dot11v btmreq candi...
Hi Meraki Community,Recently we have a poltergueist case in our hotel.Recently our manager call us to advise that our guest users can't loging on our SSID.I checked and it was true... we have 3 SSID radiating (ADMIN , GUEST and IoT) on each AP and mo...
Hi On my 5520 WLC running 8.10.190.0, I am seeing this log so much with so many different clients, here is an example: *apfMsConnTask_6: Jan 23 14:21:03.780: %APF-3-PREAUTH_FAILURE: [SA]apf_80211.c:15788 There is no PMK cache entry for client50:2...
Hello guys, Is there a way to hide or remove ssids from a specific group of APs and how can it be done in 9800 WLC ? JE
Bonjour je voudrais maitre mon Cisco 2504 wireless controller à jour. Il a actuellement là version 8.1.102.0 installer. et je voudrais passer à la version "Release 8.5.182.0" je n'arrive pas à la télécharger !! j'ai toujours un message qui vient je v...
Resolved! 6GHz transmit power
Good Morning, We are about to enable a public access WPA3 SSID on our infrastructure, and as such the 6GHz radios will now be utilised on our C9162 & C9164 APs (internal antennas). I tend to leave the APs associated with the same Default Power profil...
Hello Friedns, I have a Cisco AP C9xxx series with EWC-AP capable OS. Now I want to convert it to Capwap AP only without EWC capable. I already tried to do some solution such as execute command "ap-type capwap" or "archirve download-sw ..." to conver...
Hello.Trying to figure out the configuration via WLC on how to set up a C9120AXE-B to use the 4 ports on its face for indoors and the DART cable / AIR-ANT2566D4M-R antenna for outdoor use. Do we need to set antenna gain and TX power for the DART set...
We are replacing several AireOS controllers with the 9800 platform operating in IOS-XE. At the same time, we are replacing legacy AP models(2600/2700) with the 9120 model AP. As part of this transition, the AireOS and IOS-XE controllers will have to ...
Hi,In a network with multiple DHCP servers configured in Load Sharing mode for a single SSID, where a client's DHCP REQUEST reaches both servers but only one responds while the other rejects the client's IP request, will Meraki flag the server which ...
Resolved! Setup 2.4GHz Band Only for MR33
I need to setup a 2.4GHz Band Only for IoT devices. I saw a previous post that support needs to enable that option since I am having a hard time locate the feature in web app.I submitted a support ticket through Meraki portal but can't see any ticket...
Hey All, We are running one cluster of 9800 that is located in the campus central DC location. Then we have several distributions that are termination points of L3 subnets. Each site within the campus is connected to one of the distribution and then ...
