Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Dear All,I am trying to setup an IPSEC Tunnel between a WLC 5508 and a ISE, to perform AAA with radius protocol.I' d like setupo a IPSEC tunnel and let the radius data from the wlc to ISE pass inside it.I have configured the WLC Radius profile enabli...
As a tittle suggests, AP failed to join to WLC (C9800) after first booting. The other day, we stopped the power of AP because of planned power outage. After finishing that and AP was power on, AP failed to join to WLC (C9800). A long time ago, We cha...
Hi everyoneI am absolutely new to Cisco Spaces, but I was able to set it up with a Cisco Spaces Connector and have imported the Network Hierarchy from Cisco DNA Center to Cisco DNA Spaces.Now I am looking for a specific use case:~7’000+ employees~17’...
Hello, running software 17.9.2, and tried to install "Hitless recomended SMU, CSCwd87612, dated 23-Dec-2022.Uploaded and did a commit, but nothings happen.The status is "Upgraded and Not Impacted".What does this mean ? Any suggestions ?Upgrade statis...
Resolved! ACI and CCI
Hi there are two APs with the same wlc. When AP1 uses channel 1 and AP2 uses channel 6 or 11 with 2.4. Can we say ACI and CCI do not happen no matter how close the two AP are? Thanks
Hi, I realized the AP was disassociated from WLC and then re-joined to WLC again after 1 minute. Then from the logs, I could not find any unusual symptoms. The AP just happened to be like this on 10 July then happened again on 22 July. Can anyone ple...
Hi thereI want to make an empty port on a cisco catalyst 2960+, available/ok for connecting an extra AP Aironet 1830 under ME.Which command should I use to make the port TRUNK and any other config needed for that port?Thank you
Resolved! Error air-AP2802l-H-K9 device.
I have reset the device and i able login to Mobile Express Web UI but i dont access point.It say zero.I have i have ceck ap in cli .My connected ap shows zeroI I am assuming the it show have ap also .So it act Controller as well as AP .but ibn cli it...
AP not discovering in 9800-L version 17.03.04c
Greetings, Kindly advise how to troubleshoot no switch port led (notconnect shown in interface output) but AP 1542 is having green blinking when connected initially followed by red blinking. But switch interface showing not connect with no LED on por...
AIR-CAP2702I-B-K9I am in a position where I can get 3 for $30Unfortunately I don’t have a LAN controller but I do have a Cisco 2851 router if that helps?My current router is dying on me and can barely push out a stable connection and I would like to ...
Hi there,I have moved all the APs to new SW while we get the Cisco Switch fixed. All the AP are working fine, kept their IPs and internet working across. I just cannot access the AP controller anymore under the previous IP address at least.Any tip on...
I read about this feature in my ccna days called SELF HEALING OF WIRELESS NETWORK. Idea of this feature/ technology is that when a wireless access point disassociated from WLC. Then a neighbour WAP boosts it's TX power to plug the hole created by the...
If 2.4 Ghz is not specifically needed for a site, what steps are necessary to avoid ANY interference on other 2.4 Ghz systems? Note it is preferable to LISTEN for rogues, but not essential.1. Simply specify, for each SSID, that only 5 (or 6) GHZ is ...
Resolved! IRCM Firmware Upgrade in 5508 Controller
Hey there,I have 5508 controller running with 8.5.151.0 with some legacy AP's and now I wanted to migrate to 9800 WLC and new 9120AXI AP's, unfortunately I can't go directly, I have to keep both the setup and to support for seamless roaming (to enabl...
