Hello.Trying to figure out the configuration via WLC on how to set up a C9120AXE-B to use the 4 ports on its face for indoors and the DART cable / AIR-ANT2566D4M-R antenna for outdoor use. Do we need to set antenna gain and TX power for the DART set...
Forum Posts
We are replacing several AireOS controllers with the 9800 platform operating in IOS-XE. At the same time, we are replacing legacy AP models(2600/2700) with the 9120 model AP. As part of this transition, the AireOS and IOS-XE controllers will have to ...
Hi,In a network with multiple DHCP servers configured in Load Sharing mode for a single SSID, where a client's DHCP REQUEST reaches both servers but only one responds while the other rejects the client's IP request, will Meraki flag the server which ...
Resolved! Setup 2.4GHz Band Only for MR33
I need to setup a 2.4GHz Band Only for IoT devices. I saw a previous post that support needs to enable that option since I am having a hard time locate the feature in web app.I submitted a support ticket through Meraki portal but can't see any ticket...
Hey All, We are running one cluster of 9800 that is located in the campus central DC location. Then we have several distributions that are termination points of L3 subnets. Each site within the campus is connected to one of the distribution and then ...
Hello, one of the pairs on the ethernet is damaged, so our MR56 cannot fully function...I am thinking to re-terminate the jack with the good two pairs for 100BASE-TX Fast Ethernet. But before I do, would this work? Would our MX220 to MR56 do POE and ...
Resolved! Multiple SSID on AP managed by 9800CL
I want to configure a C9800CL controller (or any 9800, for that matter) so that the APs each run with 2-3 SSIDs. I can create setups that work with a single SSID/WLAN per AP, but I can't see how to set up more than 1 SSID per AP.Any Suggestions?
Hi,We have multiple MR74 and MR76 installed in our warehouse. All them have MA-ANT-20 omni-directional antennas installed. Now APs are mounted to ceilings (horizontally), but I read that vertical install is better for these antennas. I have a few que...
Hi,i have at a customer site one WLAN based on Meraki. We have three SSIDs configured: two corporate and one for guests. For the three SSIDs the authentication/authorization policies are enforced by the ISE (v3.3). The users attempting to get access ...
We recently upgraded our MR36 fleet to firmware version 30.5. I don't know if it's coincidental, a result of the upgrade, or if it's always been like this and I just now noticed it, but the APs have gotten "chatty" with communicating with Meraki infr...
Resolved! Reset the AP2802 password
Hello everyone,I've forgotten the console password for my AP2802, and I'd like to reset it without losing the configuration. Is this possible?Thank you.
On a C9117AXI-E I have removed both partitions using "ubi remove part1" and "ubi remove part2".I need to find a way to restore one of the partitions so the device can boot again.Any attempt in using tftp has failed so far, it seems impossible to conn...
Hi folks,How can I change the mode of 50 Cisco 1142N-K9 access points from Leightweight to Autonomous at the same time. I also have a Catalyst 3650 48 port PoE and a WLC 4400, I have tried a few things but I have only managed to do one AP at a time a...
Hi Experts!I have found setting the RxSOP too aggressive to affect client roaming. Setting it lower seems to work well however I want to understand better at what level do the AP's actually run at in the Auto mode... Overall I am trying to tune a m...
Is it impossible to use Aruba 501 Wireless Bridge with the WLC 4402 and AIr Lap 1242 Accesspoints?I have the hole WLan build with the Air 1242 AP's but now i want a WLan Bridge vor the local Lan on a hall carn to connect with the Wlan.I give the Aru...
