Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

HiI have 3 AccessPoints 1242AG running on the same subnet. To keep it simple I configured only one AccessPoint acting as a Radiuserver and on the other 2 AccessPoints I point to the correct AccessPoint(the one with the Radius configured). But when I ...

pwenger by • Level 6
  • 754 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Cisco ACS?

Hi,we have Cisco ACS Running for authentication based on Mac-Address, and I was questioned if the future is to use CiscoACS or something else? because if it is CiscoACS, then we will invest on a redudant Server. Did you ever done such configuration?

jorge.s by • Level 4
  • 587 Views
  • 1 replies
  • 0 Helpful votes

I am always getting the ''Device was not reachable via SNMP'' error messages from wlse , i confirmed the devices were up & running is there any setttings in wlse i can rectify this error messages.

akbar1 by • Community Member
  • 2971 Views
  • 2 replies
  • 0 Helpful votes

We have a site with 3 controllers it's serveral miles between them. And have think about to deploy a N+1 solution. My question is if the controllers must have same RF group. I know they must have same mobility group!. Can you have several mobilty gro...

I am trying to setup a guest network on our wireless lan. We have 2 vlan's setup for wireless. vlan 1 is our network and vlan 10 is our guest network. We are running 1131ap's and 1121g's. I have been able to get most of the 1131's working, but I can'...

dustinn3 by • Level 2
  • 3003 Views
  • 6 replies
  • 0 Helpful votes

I have not been able to follow the instructions that can along with my PAK for AIR-WCS-WLB-100EX. I must be missing something.It says to apply the license as follows: - From the Help menu select "Licensing". - On the "Licensing" page, from the comman...

jcowtan by • Level 3
  • 650 Views
  • 1 replies
  • 0 Helpful votes

Hi Forum,In terms of processing requirement, which standard(AES/TKIP/WEP) is more processing intensive, requiring more resources to process?e.g. for PDA, which one should I use, TKIP/AES for encryption and doesn't use up too much processing power. Or...

paulnigel by • Level 5
  • 800 Views
  • 1 replies
  • 0 Helpful votes

hii started to support an old (1998) arlan 630-900 installation (warehouse).there are 7 APs covering the warehouse, all set to the same channel (ch1, 910mhz) - is this correct?with 802.11b/g equipment i would set the APs to different channels 1,6,11 ...

aschwanden by • Frequent Visitor
  • 718 Views
  • 1 replies
  • 0 Helpful votes

Hi,we are using a aironet 1200 AP and Dell laptops for clients. The clients are authenticated through RADIUS (Microsoft IAS server) and AD. The problem is that we can not use the wireless client from XP to connect to the WLAN. When we use the Dell wi...

lillanita by • Community Member
  • 1396 Views
  • 7 replies
  • 0 Helpful votes

We have deployed Cisco Airspace AP with Wireless LAN Controllers (4400).Currently we have the WLC authenticating using radius to ACS version 4.01 servers.Unfortunately when the primary ACS get rebooted all the athentication requests go to the seconda...

mistryj by • Level 4
  • 886 Views
  • 2 replies
  • 0 Helpful votes

I just installed a Cisco 4400 series controller running software 3.2.150.6 I upgrade an IOS AP (1200 Series) to be lightweight. Now I cannot get the controller to see the AP. I checked the DHCP 43 option and it is enabled. The AP has a static ip of w...

amjbmr808 by • Level 1
  • 1982 Views
  • 8 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card