Hello Professionals,I have two wireless controllers and I'm about to replace one to another.WLC-A: Cisco WLC 2504 (8.3.x) - IP: 10.10.10.49WLC-B: Cisco WLC9800 (17.9.4a) IP: 10.10.10.50Two WLCs are not HA. It works independently.These two WLCs has sa...
Forum Posts
We have many sites, all with the same SSID.When Apple macOS laptops join this one problematic site, it's failing to obtain an IP unless rebooted. Looking at a packet capture taken from a laptop, it sends an 'DHCP Request' to renew its invalid/previou...
Hi Gents, When configuring a 802.1x SSID on a C9800 in 17.9.3 you can select the Security -> Layer 2 - Layer 2 security mode. You can choose from : WPA + WPA2 - and only check the WPA2 policy checkbox. WPA2 + WPA3 - and only check the WPA2 policy ch...
Hello Everyone,I have a challenge related to the WLC 5500 and associated APs (1600, 2600, and 2800). I need to change the WLAN subnet from 172.22.0.0/16 to 10.6.15.0/24. The old WLC management IP is 172.22.243.223, and the new one will be 10.6.15.10....
HelloIs it possible to change Maximum 802.1 x-AAA failure attempts values on WLC 9800 series?The documentation only contains a description of this function, but does not indicate how to change this valuesExcessive 802.1X Authentication Failures—Clien...
Please someone assist explain what is the best signal strength you can keep an Ap on? please explain the below , its one AP but i get 2 reuslts from it , i can spot the difference but what do they mean?why am i seeing two outputs?
Resolved! Power level on WLC
Hi experts,I'm trying to support the wireless radio devices better. They recommend set the Tx power level to 3 instead of dynamic selection. I just want to understand what those power levels are... Is it industry standard or is it Cisco's standard? I...
Resolved! AIRONET 1240
Hi,I am looking for CISCO AIRONET 1240 autonom firmware, the latest version ( it suppose to accept WPA2 encryption ). I cannot find to download , Can someone help me with that image ?
Hi.I have a problem on my AIR-AP2802I-E-K9 as Mobility Express. Version is 8.10.185.0. First I couldn't even see the 5Ghz option (Radio 2), but I changed the country to Germany and Radio 2 appeared. Though, the problem isn't solved. I still can't con...
Hi,Is it possible to use CW9166I without WLC?Thanks.
Resolved! 9136 AP support on 5520 WLC
While I've read the list of supported WLCs for the 9136 AP and it does say it only works with the 9800 WLCs, I was surprised to see the 5520 doesn't offer support for this, given it's still a supported model. Does anyone have any insight into this?...
Resolved! AP 1550 memory size
I see in the release notes that "From Release 8.4, Cisco 1550 APs with 64-MB memory are not supported." How can I check the memory size of the AP Regards Nikhil
Resolved! Cicso C9800-L-C boot on Rommon mode
needed to factory reset my WLC suddenly an electricity cut out while resetting when the WLC reboot it appear that there's no OS and no flash any advice on how to proceed the OS installation i already downloaded the OS that need from the cisco softwar...
Good day, I have an EWC Access Point 9120 which has an SSID with PSK and MAC filtering local, however it is not allowing me to connect the devices, it gives me a message: Jan 26 17:11:30.353: %MAB-5-FAIL: Chassis 1 R0/0: wncd: Authentication fail...
I'm trying to install anew outdoor AP (4c:e1:75:4b:f1:20) but its not joining the WLCHere is the log, I couldn't console into it aswell,*spamApTask3: Feb 02 10:12:37.218: d8:b1:90:6e:ca:f0 WTP Event Response sent to 10.10.75.169:47418*spamApTask2: Fe...
