Wireless

Goodmorning..I have a four bridge setup, two spearte SSID, with a cross over in the middle. ME*-rootA<--->non/rootA---rootB<--->non/rootB*ServerBI have a solid link over a ten mile area. Couldn't be happier with the peformance. Lan traffic does pass...

We have two Aironet 1310, connecting two office buildings. Association works fine, they get linked at 54MBit/s. But when we measure throughput, we get results between 8 and max. 15MBit/s.We can see CRC errors climbing up, but signal strenghts is quit...

Dear Sir,I would like to auto generate a new session key every 30 minutes running LEAP using AP 1200 Local RADIUS authentication? How can I configure it? I noticed there is a session timeout option under Security-->Local RADIUS Server-->User Group, i...

Is there a way to configure the Cisco ACU installation with a 352 PCMCIA card to interact with a Cisco 1200 setup for WPA-PSK.Thanks,Dan

Hi,We have 2 1300 Bridges, last firmware version.In the same room, Bridges seeing together, one is root, the other is non root, link is ok.We disconnect on bridge, going to antoher place, about 2 kilometers, reconnect the bridge. At this time, the Ra...

Hi,Any experience in configuring a Win Nt4 workstation with WPA ?I have NT4 stations, 352 pcmcia cards, AP1100, CSACS, and I want to make WPA work (with LEAP, TKIP). I am ok with w2k and xp, but NT4 gives me problems.On cisco's site I found the downl...

Hi,Any experience in configuring a Win Nt4 workstation with WPA ?I have NT4 stations, 352 pcmcia cards, AP1100, CSACS, and I want to make WPA work (with LEAP, TKIP). I am ok with w2k and xp, but NT4 gives me problems.On cisco's site I found the downl...

We are currently experiencing a problem with a few 350 bridges all on the same vlan. All 3 links are point to point 350's (root to non-root).They will randomly reset one by one, around 30 seconds apart from each other. When they come back up - they...

I have a new 1200 access point that I have upgraded to the IOS and then to software version 12.2(15)JA and installed the b/g card and antennas. The web GUI shows Radio)-not installed under the network interfaces tab. When you telnet to it, it shows...

all:i have an access point that sits 75 ft away from a wgb. the problem is the wall between them... i can't seem to get a signal to the wgb through the wall. if i move from behind the wall i can get access... is the ANYTHING i can do to penetrate the...

I have an aironet 350 wireless bridge with 12.03T firmware installed. This bridge is connected to a Cisco 2950 switch. The ports are configured as 10baseT / half duplex. I have defaulted the bridge, reloaded firmware on the bridge, restarted the b...

I have two 1200AP's set up and am trying to get one working as a repeater for the other. We are doing EAP-TLS authentication for our network, but for the repeater to authenticate I enabled LEAP on the ACS server. I added a user on the ACS for the rep...

I cannot configure the external antenna on this AP1231. It will not let me type anything in the box where you set the antenna gain. It says that it should be -128-128, but it wil not let one put anything into the box after you check the enable button...

Any news about wireless switche of the cisco ?I´m started one project and people talk me about this system from symbol. Any about same system in cisco ?Regards

I have a problem with the connection/quality of speech when standing within 2-3 meters away of an AP with a 7920 phone. Also The connection to the CM is broken sometimes. (Also during a call) after the call drops the phone will connect to the CM auto...