Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

I am replacing an old C-Spec wireless bridge we have between our main building and a building down the street. I am having a problem getting the two 1310's to associate with each other. I have reset them to defaults and configured a ethernet ip on ea...

jjn2002 by • Community Member
  • 745 Views
  • 3 replies
  • 0 Helpful votes

We are looking at using Cisco Leap and was told that Leap can only handle up to 50 clients. Is that true?First post here. Hopefully I'm at the right place at the right time.Pdub

pwilliams by • Community Member
  • 599 Views
  • 2 replies
  • 0 Helpful votes

Dear Sir,[1] Does Cisco offer NEMA enclosure from its product line? If yes please specify Part No. for Cisco Aironet 350 series and 1300 series Access Points.Thank you,Best Regards

I have tried to get the AP1100 running as a workgroup bridge, but no success by now. I am getting the following output:*Mar 1 00:26:53.917: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No matching privacy setting (from 000e.d7b1.3400...

Hi,I'm using a LMC352 Aironet PC Card on Mac OS X with the 3.0.1 software. If I see multiple SSIDs in range with the same name, how can I select one over the other? The software does not seem to consistently select one with the best signal. This is f...

trainscape by • Community Member
  • 592 Views
  • 2 replies
  • 0 Helpful votes

I am having problems with Windows AD - expired password to sucessfully change when doing EAP-FAST authentication and TKIP data encryption. Configuration is: Windows XP & 350 card & ACU 6.5.01 on the client. 1200 AP - 12.3(4)JA &Cisco ACS v3.3 authent...

parl_ip by • Community Member
  • 676 Views
  • 2 replies
  • 0 Helpful votes

I am planning to implement Wireless security with Cisco Access Point 1200, ACS 3.2.3 with 802.1x and EAP-FAST as authentication method. I am clear with te technologies used in EAP-FAST but i would like to know that what is required at client PC which...

manishkbohra by • Community Member
  • 1110 Views
  • 2 replies
  • 0 Helpful votes

I have a Sony camera ~1000 feet from my 1300AP. So I ran 300 feet of RJ45 to a NEMA box with a Linksys 5 port switch and a WGB350 inside. I can log onto the bridge from the root LAN and I can ping the camera from the bridge. The bridge is associated ...

I've a doubt about the power level to set to follow European standard (100mW max) with an 1300 ap with 5.2 DBi omnidirectional antenna AIR-ANT2506..Can I leave the default (50mW CCK and 30mw OFDM) or I've to reduce the power in 802.11g settings to 20...

vincenzos by • Community Member
  • 507 Views
  • 1 replies
  • 0 Helpful votes

I had a request to setup a 1231G Access Point and to have it act as a DHCP server, but only for the Wireless interface.

ereinoehl by • Level 1
  • 406 Views
  • 1 replies
  • 0 Helpful votes

Hello,First let me start by saying that I am a novice at wireless networks. I have been working on/around computers and wired networks for about twenty years but I am learning about wireless and have probably bit off more than I can chew with this pr...

brandon-f by • Community Member
  • 872 Views
  • 3 replies
  • 0 Helpful votes

Hello, we get an error message in logsfor wireless clients on our WLSE appliance we cann't explain : event=IP_Address_Change. But we didn'tchange any conf...Any idea ?Regards, C.Rolland

chrolland by • Visitor
  • 991 Views
  • 2 replies
  • 0 Helpful votes

My goal is to install a Secure ACS and a WLSE box to control my wireless environment and to deploy NAC. As with any company the cheaper I can bring this in the more chance I have of getting this approved. Therefore I am searching for some Cisco Press...

silkysilo by • Community Member
  • 531 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card