Wireless

dear alli have 2 offices distance between them is 3.5 kilometers. i want to link between them thru 1400 series bridge.but i'm not clear abt the location, bcoz the next office is 3.5 km away so i dont know which side it is, so in this case, how can i ...

I am having a problem with a WLSE 2.11 template on a 1210 B/G Access point running IOS 12.3(4)JA. I am configuring as follows:The encryption for the VLAN in question (I will refer to it as VLAN X) is Cipher/CKIP.The SSID config for the VLAN is EAP, n...

HiI would like someone to confirm my knowledge of the behaviour of the WGB 350 with the population of its mac-address-table.My customer uses the WGB to connect multiple industrial PCs to the WLAN in a big hall. The PCs are placed wiedspread, and when...

Hi , I have had continously message of this in a syslog :Jun 18 11:11:46 192.168.4.216 5595: *Mar 3 21:03:39.726: %DOT11-4-TKIP_MIC_FAILURE_REPORT: Received TKIP Michael MIC failure report from the station 000f.f778.e28a on the packet (TSC=0x16000000...

hi guys,Does cisco have any wireless frame capturing softwares? I mean the technical stuff. the software must be able to capture frame format e.g (frame control, duration, da, sa,bssid, sequence control, ssid IEe, support rate ie, etc....ive tried et...

HiI am looking for an access point that can also make a serial (9 pin) connection to a GSM modem. Any one have any ideas??RegardsMalcolm

Hi...Anyone who knows if the xml-ready firmware for the 7920 is already in his final release ?And, if yes, what's the version of CCM you should use ?

Hi,I have some AIRONET 350 series workgroup bridge with the 8.85 softwareI put a WEP encryption based on 128 bits pre shared key.But, in order to increase security, i would like to deploy WPA with PEAP.I saw this message: http://forums.cisco.com/efor...

Hello Guys,We want to develop an application similar to ACU, basically we are interesting in getting the signal strength. Once we got the acceptable level of signal strength, we will send data to the server. Is there any programming development sdk c...

I need to get the Gina that comes with ADU 2.1 (cscogina.dll) to interoperate with the Gina that comes with SecurID for Windows Authentication Agent 6.0 (AceGina.dll). Is this currently possible? Will it ever be possible?Both Ginas currently have to ...

Lot's of devices are staying with "No Data Yet" for ever in all the fields to be verified. Already waited, rebooted, etc... but devices are staying with no data yet... any clue what this means?

I am deploying an AP1231 infrastructure managed by the WLSE. The goal is to cover some factory for wireless handheld barcode scanners in telnet client mode. So data throughput is not important. My intent is to use as low power as possible. Is it poss...

Hi,I've just logged a TAC case on this one, but has anybody seen lower than expected dbm levels when just testing 1310 bridges in a lab? I've got them a few feet apart connected to the injectors with the short white f type cables. They're running 12....

I have a network covering a fairly wide area. the central node is a BR352 with BR352s and AP352s and AP342s operating as repeaters. All have 12.04 firmware. Normally all "home" on the central BR352 node. "Occasionally" the (one) AP352 repeater unit d...

does anyone have any info other than what is available on cisco's website about configuring an aironet 1200 ap that belongs to a WDS but allows client authentication?I followed the notes on the website, and managed to configure my ap as a primary WDS...