Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello !Anybody else using this version and discover that NTP is gone or is it a bug ?Reading the release notes, I can't see anything regarding NTP support is removed.Temporary solution is to re-configure to SNTP.
one of our site, customer observe that they have all the AP connections reset. Please find attached logs *Mar 1 00:00:04.525: soap_pci_subsys_init: slot 3 found radio*Mar 1 00:00:04.826: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset*...
Does the WLSE support Cisco 2950sx series switches? I currently have serveral buildings with 2950sx-24's and 2950sx-48's with 1100's 1230's and 1130ag AP's attached and when doing discovery the WLSE reports that the attached switches are unsupported....
I am trying to help a client out of a small jam. They have a pair of 1200's that they were planning to use with external antennas to bridge the gap between two buildings. It looks from the documentation that I can not do this. Just want a sanity chec...
Is there an easy way to retrieve the serial numbers from Aironet access points other than climbing into a ceiling and reading the serial number off the unit itself. Can I find it somewhere by using a command?
When i am trying to apply new firmware -12.3(4)JA- to an AP1210, WLSE alert me when saving job :: Job protocol validation ... Passed Image version validation ... WarningDetails ... Imagec1200-k9w7-tar.123-4.JA.tar (12.3(4)JA ) Not recognized. Device-...
Hi,One of our customer is using two 7920 phones through two AP1200 access points with IOS 12.3(2)JA, in a room.The customer experienced reset of 7920 frequently from the beginning.However, after we changed RF transmission power settings for AP1200, t...
On several access points (14) in our environment the following messages are logged repeatedly:Stopped driver for port "awc0"Started driver for port "awc0"A reset of the config was recommended, but this did not solve the problem. Clients cannot authen...
I have 2-cisco wireless brigdes that are having problems associating. The topology looks like this:cisco350WB-omni <----------> cisco350WB-yagi10.1.1.4 /28 10.1.1.3 /28root bridge bridge w/out clientsI plan to connect more bridges in the future to th...
Got a pair of 1310 running IOS 12.2(15) with external antenna, 4km apart, and 1 PC on each side.I'm just using MAC authenticate and filters with the trouble of SSID broadcasted and no local RADIUS server.What's best in terms of security config? How t...
Hello we have a number of Aironet (Before Cisco) Wireless AP's, it's the model Aironet 4800 Series Turbo DS Model# AP4800-E, and I was wondering if they were WPA 2.0 compatible and if there were any upgrade kits to make them compatible if they are no...
We are running WPA with MAC Filters on a 1100 Version 12.2.15 JAWe keep losing association to the AP for no apparent reason. To get it running again we are forced to re-seat the 350 Card or reboot the laptop.Here is a little from the AP Log. Apr 11 1...
Has anyone got any experience of all of the above. Some background - The FWSM is in transparent mode, using virtual contexts between the VRF and the main routing table to ensure relevant mobility traffic passes through the relevant security context.I...
I have a 340 series AP and have already installed the driver for my 350 series PCMCIA LAN adapter.I've checked that the AP has a valid IP (10.x.x.x) assigned to it(on our core LAN switch).I get a 169.x.x.x IP address.The Aironet Client Utility(ACU) s...
Hi,Since a was browsing through this forum I noticed that there are lots of problem with DHPC request and the AP 1200. Well here is another "simple" problemOne "out of the box" AP1231 Upgrade to IOS : c1200-k9w7-mx.123-2.JA2Configuring SSID and WEP 4...
