Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi - I have 1 access point for a small office. I wish to have 2 VLANs, one for guest users who bring their laptops into the office, and one internal vlan for company users who need access to the internal resources of the office. Reqs:1. Guest users o...

tkadri by • Level 1
  • 830 Views
  • 1 replies
  • 0 Helpful votes

I have installed 10 Aironet ap's throughout the bldg. All ap's are mounted from ceiling with antennae pointed down towards floor. I have been asked what the radiation pattern is for the antennae. I'm using 2 dipole antennae that is standard for the a...

bm_5789 by • Level 5
  • 868 Views
  • 4 replies
  • 0 Helpful votes

I am having a delay authenticating to my Aironet 1200 when first logging on using WPA to ACS3.3. My login scripts are not executing because of the delay. I installed the Microsoft patch KB826942, but still have the problem. No delay if I logoff then ...

triplesb by • Community Member
  • 719 Views
  • 1 replies
  • 0 Helpful votes

Hi bruce, we've implemented a wireless network in a school recently. there are about 30 access points covering the whole school but due to the construction we can see about 11 access points at any one time. my question is reagrding channel set up. we...

andy.butler by • Community Member
  • 852 Views
  • 2 replies
  • 0 Helpful votes

Have set up 2 VLANs on the AP but can only access the one that has it's SSID broadcast in the beacon. If the VLAN does not have it's SSID broadcast it is not seen by the laptop (tried 3 different one and a PDA). Can swap which SSID is broadcast and e...

sw1 by • Level 1
  • 684 Views
  • 2 replies
  • 0 Helpful votes

I have an issue where a Cisco cardbus adapter causes a PC BSOD on whatever PC or different Cisco card is used. This only happens with Cisco a/b/g Cards and 1230 APs and only in a certain AP area of the building.Has anyone else ever experienced this?

sthomas by • Community Member
  • 811 Views
  • 3 replies
  • 0 Helpful votes

Hi- Is it possible to Change MAC-Adress of a AIR-PCM352-Card ?my driver version is 7.29.0.0 (01.07.2001)- How can i update the firmmware of this 802.11b-Client-Cardis this possible with Tools ACU 6.3.011regards,Ralf

rnolden by • Level 2
  • 607 Views
  • 1 replies
  • 0 Helpful votes

On the RadioG settings :CCK Transmitter Power (mW): 100 MaxOFDM Transmitter Power (mW): 30 Maxwhat is the difference between setting it to Max or to 30 or 100?They would both seem to be the max.

bob.schwartz by • Community Member
  • 1069 Views
  • 3 replies
  • 0 Helpful votes

hi all,i've a problem with my Aironet adapter 350. My problem is that i could not use the 128 bit for it.i just can choose 2 value 40 bit and 104 but not 128bit.my laptop uses window xp.

tuan-nguyen by • Community Member
  • 579 Views
  • 1 replies
  • 0 Helpful votes

I have just inherited the network which houses a 340 Bridge with early 8.08 firmware. My problem is, the previous administrator password protected causing the configurable attributes to be readonly while I connect with a serial cable.I really need to...

chitchcock by • Community Member
  • 699 Views
  • 2 replies
  • 0 Helpful votes

I have a client that asked me about a situation where they have a school with three floors and around 6 classrooms on each floor. It's a small school. A company wants to install 21 Cisco 1200 AP's in each room and in the hallways. The school wants al...

Hi, muzhiki!I have AccessPoint Cisco AP340. And i whant to get statistic to Linux by SNMP. I set SNMP Trap Destination and SNMP Trap Community. But, when i run command on my Linux-box (snmpwalk -v 2c -c XXXXX aaa.bbb.ccc.ddd), he not answer to me. Wh...

Review Cisco Networking for a $25 gift card