Wireless

What are the ramifications between having an antenna set to horizontal versus vertical?One of our techs set the 19 dbi sector antenna to horizontal. this seems to have given us about 160 degree coverage from a 90 degree sector antenna (was 90 degrees...

I have 802.11a implemented in a warehouse environment. 4 AP's total. about 25 clients. Unfortunately the equipment is not cisco but I'm looking for 'general' info that should apply to all 802.11a and I'm sure there are plenty of knowlegable people in...

I am setting up AP1200 and trunking 2 vlan and setup two SSID. This is what I wanted to do. Have one vlan and ssid that is not restricted, this SSID and would be broadcasted. People with out of the box confiured client would connect to this net get a...

I only have four clients to this access point, which I have hard coded the SSID on to them. I want to keep programs like NetStumbler from knowing the AP is there. I have WEP, TKIP, and MIC installed for security I just figure if you can keep someone ...

Is there any possibility to get more than 11Mbps of transmission speed over wireless bridge, .e.g binding 5 wireless bridges to get 55Mbps?Thanks.

I have a AP 350 series connected to a 826 ADSL router. I have no problem what so ever with my internetconnection because I used the same setup with a cable connected to the 826 and I didn't had the problem.My problem is that after 50 minutes or so my...

Hi,I am in an environment with unstable power supply. We deployed APs and Bridges within a 700 meters radius. We use very reliable solar system at the base. Can I use PoE beyond the traditional 100 meters to provide ONLY power to the equipment over 6...

I successfully connected a DLink AP (DWL900AP+), as client mode to my Cisco AP350, but it only connects to AP if I set AP352 to Allow "Broadcast" SSID to Associate. The docs says: "Use this setting to choose whether devices that do not specify an SSI...

HelloI have an Aironet350 AP which I've integrated with CSACS to provide LEAP authentication to wireless users. This may seem similar to other posts regarding DHCP and aironet, but in my case, when I plug my wireless PCMCIA card into my notebook and ...

I am considering a job shooting 18 miles to an island. Has anyone done anything like this? If so how stable is it? How long did it take to align the dishes? I have read all the specs but I would love to know of a real world working deployment before ...

Had Aironet 4800 PCMCIA card running fine under WIN98SE. Upgraded system to WIN2000-PRO, loaded new drivers, firmware for 4800. Associates and then drops conn. due to "Radio on 4800 is turned off". I turn it back on and in less than 1 minute same thi...

We have LinkSys access points in two remote buildings. We now want to connect the two buildings with a Cisco Aironet 350 Bridge. The bridge link works fine. The problem is every 30-60 minutes the LinkSys devices have go to a wonderful 14.4k (or slowe...

IODs to find the details of the Swich on wich the AP is conected.iso.3.6.1.4.1.9.9.23.1.2.1.1.5.1.1 = "Cisco Internetwork Operating System Software .IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC3b, RELEASE SOFTWARE (fc1).Copyright (c...

As unbiased as possible, is it better to use ACS or W2K Server to setup PEAP with ACU6.0 (CB20A adapter) and 1220 AP? WHY?

Does Cisco have any near future plans of an 802.11a bridge? I am needing a wireless component capable of trunking multiple v-lans with the available bandwidth to support both data and VOIP. We are currently using 350 series bridges and access points,...