Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
We have LinkSys access points in two remote buildings. We now want to connect the two buildings with a Cisco Aironet 350 Bridge. The bridge link works fine. The problem is every 30-60 minutes the LinkSys devices have go to a wonderful 14.4k (or slowe...
IODs to find the details of the Swich on wich the AP is conected.iso.3.6.1.4.1.9.9.23.1.2.1.1.5.1.1 = "Cisco Internetwork Operating System Software .IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC3b, RELEASE SOFTWARE (fc1).Copyright (c...
As unbiased as possible, is it better to use ACS or W2K Server to setup PEAP with ACU6.0 (CB20A adapter) and 1220 AP? WHY?
Does Cisco have any near future plans of an 802.11a bridge? I am needing a wireless component capable of trunking multiple v-lans with the available bandwidth to support both data and VOIP. We are currently using 350 series bridges and access points,...
How do you enable SNMP on the AP1200 and how do you add the community strings to the AP?
The problem is that LEAP doesn't try to authenticate until almost a minute after my desktop loads. So, my scripts don't run and anyone that doesn't have a cached profile would not be allowed to log on at all.I downloaded the full Funk client and ther...
I need to design a windows XP application that will monitor if my Aironet 350 is connected to a WLAN. It will also need to monitor other parameters such as signal strength, error rates, etc... I have not found anything on Cisco site (library, interfa...
I need to design a windows XP application that will monitor if my Aironet 350 is connected to a WLAN. It will also need to monitor other parameters such as signal strength, error rates, etc... I have not found anything on Cisco site (library, interfa...
I have problems trying to connect an older Telxon PTC 960 that works fine with Access Point (Aironet old type), but can´t connect to Access Point Cisco 350.The error is Network timeout.The terminal connects OK to Lucent 802.11b compliant Acces Point....
Hi, Our External 350 Bridge and internal 340 AP alway lost connection with ethenet network. Look link the device been attack by some heavy traffic. But the question is why only the wireless equipment. ThI problem will not occur if I connect the equip...
I'm trying to set up a wireless network using Network-EAP on the AP (aironet 1200) with a Certificate Authority and Internet Authentication Service enabled. The client will not get an IP address and the AP log shows that it associates with the client...
I have installed several WLAN’s over the years using non-Cisco equipment. However, I’ve ‘seen-the-light’ and have deployed a WLAN using two Aironet 1100 access points. My question is how do I allow my clients to roam between the two? In my previous i...
Hi, I am using 1200 access points. Now I need to authenticate any user when they access the wireless network through cisco ACS 3.0. Please help me to configure Radius on ACS and Radius configuration on Access points. Urgent reply is highly appricite....
does cisco 350 workgroup bridge and Bridgentransparent for 802.1Q frames ?I mean that if the 802.1Q tagged frame enters WGB's or BR's ethernet interface can it leave wireless interface unchanged and vice versa ?
I would like to ask you the experts the same question that I get asked many times by my customers with regards to how secure is a 802.1X enabled wireless networks.I constantly get presented with reports by security experts deeming Wireless as not sec...
