Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
HiCan someone explain me how to get the MAC WILDCARD MASK value for a MAC ACLThanks
Internet access available. WLC has HTTP access to the Cisco License Portal. WLC#ping tools.cisco.comType escape sequence to abort.Sending 5, 100-byte ICMP Echos to 173.37.145.8, timeout is 2 seconds:!!!!! How does WLC find SA (Smart Account) and VA (...
I want to use the Air-ap1562i-e-k9 access point in my office garden, I connected it to the router with Cat6 cable (with PoE Injector), when I turn it on (led is red for 5 seconds) and (blinking green for 1 minute) (green, red and yellow) turns) and a...
Hi everyone,Clients of wireless networks keep roaming between APs while having good signal strength and stable connection. Some cases we observed that clients roam to worse signal strength radios on their own, causing impact for the users during vide...
Hello,I'm inquiring about the location where I should direct my attention to identify any DFS (Dynamic Frequency Selection) events. Our wireless access points are operating on DFS channels, and we've been receiving reports of WiFi disruptions. I have...
I work in the IT department at a medium size high school (about 1000 students). During passing periods the wifi mostly stops working. My theory is that this is due to the huge number of devices that are all on the move simultaneously (roughly 2000 de...
Hi all,Last few years multiple topics in this community were about the limitations on the MR46E's transmit power in combination with one of the MA-ANT-3 models.example: https://community.meraki.com/t5/Wireless-LAN/MR46E-Too-low-2-4-Ghz-transmit-power...
as we know, per design new access point will get default tag policy, tag rf, tag site and will not provide wifi.I have N+1 WLCs and its quite inconvenient manually assign tags for new access points and then need not to forget configure such static as...
Hi Community, Recently high bandwidth consumption on WAN was reported & i was provided a list of DCs & AP (MRs) that were seen downloading & uploading data. This was captured on the gateway (L3/FW) which is managed by a different vendor. I'd like to ...
Hello,How to configure authentication for wifi devices that are not able to login by itself.Use a local user and password database in meraki dashboards? no radius.Devices using its mac address as login.Devices using its mac address as password.Thanks...
Hi, Suddenly one of our 1832 stops working. In serial console I get repeatetly output like this GPVTG,,T,,M,,N,,K,N*2C $GPGSA,A,1,,,,,,,,,,,,,,,*1E $GPGGA,,,,,,0,,,,,,,,*66 $GPRMC,,V,,,,,,,,,,N*53 $GPGSV,3,1,12,01,08,240,,03,45,135,,04,62,240,,06,2...
Hi I have performed 'clear config' and 'reset system' commands on two access point CISCO 1850 with same result.After reboot I have done the configuration (administrative account and SSID parameters).But on both AP, after restart, I can login but the ...
HI AllI am getting the below rogue AP alert, the devices are Windows laptops, internet sharing is disabled so it's not that. This alert happens at least once a day and I have run out of ideas to resolve it. 1 rogue AP on the LAN network in the xxxxx ...
Hello Dears,I've a question, and appreciate your support.If we roam from AP group 1 to AP group 2 and had to re-associate then would we receive an IP address from AP Group 2? if yes, how could that be performed? wouldn't that go against L3 roaming fe...
Hi,We have some branch offices with Aironet 2700 and 2800 access points and old WLC 2504 running 8.5.151.0. As the WLC 2504 are beyond end of life and support for Aironet 2700 and 2800 has been re-introduced with 17.9.x we migrate our old access poin...
