Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Cisco Licensing
Hello all, we bought C9800 CL + C9105 AP's with 3y DNA licenses. I got an email with confirmation that licenses and support were assigned to my smart account. However, in licenses i see only perpetual network stack licenses, no DNA licenses at all. M...
1. Will extending the omni antennas away from each other and the MR86 base impact the benefits of the 4x4 MU-MIMO?2. Do all 4 antenna ports of the MR86 carry both 2.4 GHz and 5 GHz radio signals?Thank you,Gil
I'm currently running a POC using Merkai Cloud with Cisco AP's to setup a small WIFI environment.The Merkai Cloud can see and connect to our OnPerm Cisco AP's - All great..The major problem I'm having is when I try and get Cisco ISE to handle the EAP...
Hi,I have a problem with my Cisco 3602i, i've reseted it but it always blinking blue-green-red.I'm using a TPLink POE Injector up to 60w, i can see my 3602i in my switch with an ip adress i can ping it but i can't connect to it in SSH it always say "...
Hi all, I am going to upgrade my mobility express step up ( Air-2800) to 9800 WLC. I am facing a challange where all my APs are configured with static IP and WLC IP , Now we are changing Managemnet subnet where the new 9800 will be placed.is there an...
I need some help with setting up the bootstrap servers for doing secure ZTP through automation. I have found a few articles :To create the Bootstrap server: https://www.rfc-editor.org/rfc/rfc8572.html#section-4.4But this example does not do a live de...
Our 9800-40 WLC has 342 APs connected. We have a combination of 3702, 3802, and 9120 APs. Some of the connected APs are showing up as malicious rouge APs.
Hi Everyone,I have created splash page to access the internet with radius server. But splash page is reflecting again and again with average time of 1 hour even if user is already connected and got suddenly disconnected due to splash page reflection....
I have:1 Wifi Controller: SSID Staff (Subnet 192.168.10.024)1 Wifi Controller: SSID Product (Subnet 172.16.10/23)All are centralized control at DNA Center.And 802.1x authentication (ISE and Radius on window server).Between the SSID Staff vs Product i...
Hi, I have a 9800wlc pair running on RP redundancy sso. I need to change it now to use RMI + RP redundancy mode. could someone share the complete steps I need to follow to configure this? I understand that wlcs will need to be reloaded for config...
On the firmware upgrade manager page, the template for one site shows a status of "Critical" with very old firmware but the devices covered by that template show a status of "Good" with the newest firmware. Why does this happen, and how do I fix it?
When i connecting in my SSID, no automatic redirect to https://1.1.1.1/But when i enter url https://1.1.1.1 with my hands everything is ok working ! 1) ipconfig - correct2) DNS resolving - correct3) WLC-> controller -> interface -> Virtual -> ip add...
after creating a new WLAN, I get the connection to that SSID, get the right IP address, and can go to the internet, and intranet, but couldn't SSH or HTTPS to the WLC. it is pretty weird, any one has any idea about this? thanks in advance.
Hi all,I have got a template, where 200+ networks are bind to.In this template is an SSID secured by PSK. So all sites have got the same.Some staff is traveling around and already got to know the PSK. Is there a chance to block these MACs all over th...
Hello everyone,I want to apologize in advance for my ignorance, as I am not well versed in networking - our network admin left our company and I am just learning Meraki as I go to help.Our current setup is that when connecting to our corp network, a ...
