Hello we have a C9800-CL and 9115 access points in flex mode. When we install wireless at a new site, we always need to wait for the first access point to download the firmware from the wlc at the data center and that takes time, because of the WAN l...
Forum Posts
I have a scenario where we use ISE for EAP-TLS cert based authentication for wireless network. It has been working at our HQ for several months. Now we are trying to roll this out to our remote offices that connect to HQ over private WAN links.The is...
Hi ,Active WLC uplink goes down, when check the HA status we can see the below information, how to resolve this issue please suggest meWLC-9800-01#sh redundancy statesmy state = 13 -ACTIVEpeer state = 1 -DISABLEDMode = SimplexUnit = PrimaryUnit ID = ...
Has anyone had any issues with solarwinds and the amount of alerts it puts on AP's? I have had several alerts for AP's down for more than 15mins. However on the WLC for uptimes the AP's do not show any issues of that happening. There should be som...
Hi awesome geeks!been trying to access that AP via console port, in order to make the first config ( autonomous ) using putty;Baudrate:9600Data: 8 bitParity: noneStop: 1bitFlow control: Xon/Xoff & none ( tried both )But nothing works.. So i appraciat...
Hello,I recently connected a new CW9166i-B access point and it's stuck flashing red & green. It successfully authenticates via ISE, gets and IP address but doesn't show up on the WLC. I can ping the IP from the WLC and ping the WLC from the switch. B...
Resolved! Roaming and vWLC
Hello! I have a vWlc (v 8.10.185.0) and some access points (2802i's and 2702i's). When clients move in the building the clients won't roam from ap to ap. If they do, the client disconnects form the wlan and then reconnects instead of roam. What is th...
Hi,i am trying to upgrade cisco wireless controller AIR-CT2504-K9 from version 8.3.140.0 to 8.5.171 , I've uploaded the image via gui to the wlc,(Cisco Controller) >show bootPrimary Boot Image............................... 8.5.171.0 (default)Backup ...
Hi everyone;We are facing a strange issue on the model 2700 with 9800 WLCDesign = Branches are setup as flex connect APs, WLC is located in Datacenter and the connectivity between Branch and DC is sdwan. For some reason AP 2700 are restarting sporad...
I have a lightweight access point AIR-CAP3602I-A-K9 with an AIR-RM3000AC-A-K9 ac radio module installed. The AP has a couple of built-in radios, one for 2.4 GHz and the other for 5 GHz that supports WiFi n at most. All works fine except that it appea...
Has anyone else experience of running an Enhanced Open with transition WLAN?I have seen that most devices treat it correctly and only show one network in the list of available networks. Windows 10 and 11 however show the hidden network also which cus...
hi team, i have AP 9110AXID when i taken console it has EWC and i want convert capwap and join to wlc 9800 how to fix it
I am trying to setup Passive client on 2802i Mobility Express (v8.10.151.0) so that when I set the bridge mode on vmware for client Windows 10, I directly get the IP from the router. This worked fine on WLC 2504 as per my previous post (Solved: Re: W...
We have two Cisco Meraki and need to renew these devices. Please help with this request.
Hi Guys,I cannot find few access points in WLC 9800 All APs are connected to switch and all interfaces are also in same VLAN.The thing is when is shutdown the switch interface, One AP is shown less in count in WLC 9800. When I turn on switch port AP ...
