Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
HiHave several 8500 and 5520 in HA, we monitor both active and standby WLCs using SNMP v2 in Solarwinds.Had to start to monitor using SNMPV3The 8500s are running 8.5.182.104 - I can monitor both Active and Stanby WLC with SNMPv3The 5520s are running ...
Access point is able to see ( ping ) WLC and vice-versa but not able to join Wireless Controller WLC 9800 - software version - 17.3.3Access point 9130AXI- B - software version - 17.6.4. Please check the error below on AP Please refer to error log on ...
when do we actually predownload the image to AP + image swap and AP reset in C9800 WLC image upgrade?i follow the guide; it states to # AP image swap then ap image reset which will cause the AP to reboot then to #install activate the image on the WLC...
Hello All, In addition to the DNA license for APs, do I need any other licenses so that one pair of 9800-L (Active/Standby) can work without issues? Do I need the PERF License in order for the HA to work? Thanks,
Anyone out there noticed any issues with HP G4 Chromebooks and MR46 APs?We have newer Lenovos and New HP Chromebooks that do not exhibit constant connection drops.Observer behavior:Chromebook disconnects and reconnects to same AP every few seconds.So...
We are getting a lot of IP address thefts with Chromebooks that has started happening recentlyWe are using a Cisco Catalyst 9800-80 Wireless Controller with ver 17.6.3Anyone have any pointers?Dave
Hi Guys, we are installing new Cisco AP with external antenas of model C9120AXE-E. Anyone have document which help me to see pictorial view of best antena positions?
hello, I forgot my pi server backup password. Is there any way to check?
Hi there, We have had to configure an IW3702 in the middle of the Root AP and Client AP eg: RootAP <----------> RepeaterAP <---------> Client AP From the repeater I have an established connection between both RootAP and ClientAP, however neither the ...
Hi All,I'm working on a group of IE2000s connected by multimode fiber. I have 10 instant's and configured the same way and 9/10 are functioning properly, but that one won't communicate on either fiber port. I've checked the transceiver detail of both...
Hi, I've been asked to source an AP for an ATEX environment. The AP specifically needs to be Zone 22, which I believe is Class 2 Zone 2. I'm quite new with installing an AP in an ATEX environment, but I'm struggling to find an AP that isn't Class 1 Z...
Can I use AP iw3702 on ATEX Ex Zone 1 or 2 classifed areas? if not, which one is recommended?
Hi, I have an 1800s running legacy software version. When I try to claim it with a 2.x DNA Center I receive an error, stating the CiscoSensorProvisioning SSID is not supported with the current sw version of the sensor. This is expected, as the DNAC d...
Resolved! WLC 5520 Service Port
Hello,I know the Service Port is used for OOB management, however, when testing this in GNS3 in my lab using Putty to connect to the service port, I thought I should be able to see the boot process ? At the moment I can onyl see the CLI once its boot...
Hello AllLooking for help on troubleshooting access point 9130X. I have DHCP server/scope running on Cisco 9200 ( switch 1 ) and can see it is handing IP address to AP but I am not able to ping/reach Access point. I have switchport setup to access po...
