hello,i get the problem my AIR-AP1832I-C-K9 , how can this problem solve please help me. please tell me details .thanks you. (RNAQ-C7) # resetresetting ...U-Boot 2012.07 (btldr release 38) (Oct 29 2019 - 06:39:45)This product contains some software l...
Forum Posts
according to high availability deployment guide 17.3 for C9800 WLCs there are 2 options for Redundancy: via RP Connecting a C9800 wireless controller HA pair to upstream switches Prior to 17.1 following topologies were supported in terms of upstream ...
when user connect Guest SSID with Central web ISE auth, ISE is getting access request and access accept request only no further communication. below are client logs on WLC *apfMsConnTask_0: Oct 07 13:21:26.788: 54:8d:5a:67:a7:3c Max Client Trap Th...
Resolved! Deauthentification client
HelloThese new laptops with 802.11ax have WiFi disconnections in some of my clients' devices. I was able to fix discovered a way to prevent them more easily I update drivers up to date and force 5hgz. The identical pattern is now on fresh laptop. I w...
We have established mobility between 9800 L C and AireOS model 3504. On 9800 WLC, I can see couple of client info shows AP name as 3504 WLC ip address. Does it mean mobility working as expected?How I can verify mobility is working fine?Thank you.
I work for a municipality, and I am trying to decommission our old 5500 controller and migrate/update all our of APs to our 9800 (17.6.2). I have three APs I noticed and finally found that a predecessor had set up for the local university that bought...
Hi I recently purchased a few 240ac APs and mesh extenders to replace an existing WAP321 deployment. Unfortunately my experience has been pretty bad so far with them and I am hoping its just my lack of information. I have done the initial setup and...
Good Day,I set up ten Cisco 140AC (CBW140AC-A-CA) access points for one of my schools this week. I used the Cisco Business App to configure them (set up SSID, named each of the ten units AP01-AP10). I didn't set static IPs as I couldn't see that op...
Hi,I have a C9800-40 controller that does not send all configured telemetry data to our Telegraf/InfluxDB. Some subscriptions are sent, some not. This worked flawlessly for a few days, then some subscriptions stopped working without any change on our...
Hi,when we used FlexConnect, all the APs logged every single association and disassociation of a client, i.e.:%DOT11-6-ASSOC: Interface Dot11Radio0, Station aeda.0a63.xxxx REAP Associated KEY_MGMT[Open]%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauth...
In DNA Center on client assurance we can see clients datarate. Is this datarate tx or rx from the clients perspective?
We use Cisco Meraki APs with WPA2 Enterprise authentication againsts remote RADIUS server with EAP-TTLS + PAP.When user provides wrong credentials (bad password), RADIUS sends Access-Reject message to the AP.AP the disassociates the endpoint providin...
Resolved! 9800 License status
Hi Team, As of now , we have not enabled smart license in our newly installed 9800-L controller but still i am seeing in output as enabled. As per document of cisco, its mention if you not installed or add smart licenseing , it will come up as evalu...
Hi team, We are migrating 2700 AP from Aireos to 9800 WLC . Both Aireos and 9800 WLC are in same network. AP regsitration for Aireos controller based on DHCP option 43. When we move AP manually by defining static controller Ip address (i.e. 9800 WLC...
Resolved! WLC 9800 CL Client Exclusion Issue
We have spoke sites on Flex mode, each site are all treated separately, has its own DHCP server to serve wireless clients. The DHCP scope is the same for all sites. Now with WPS IP Theft or IP Reuse enabled it seems that when Site A client is served ...
