Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Wondering if anyone can help me. I'm troubleshooting a AIR-CAP3502I-AK9 Access Point. When I first opened it through console it said there's no bootable IOS image on the device. So what I did was connected it through Hyperterminal with these settings...

feniss by Community Member
  • 1790 Views
  • 3 replies
  • 0 Helpful votes

Hi Cisco  Community.I have an issue with AP AIR-CAP1532I-E-K9 with image LW ap1g3-k9w8-tar.153-3.JK7.tar.It's not able to join WLC.My WLC is:NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"PID: AIR-CT5508-K9, VID: V03The version o...

Good day,i need a help to set up wireless network at my office.I have cisco 1900 router which will be connected to ISP. Then the plan is to connect cisco Wireless controller 2504 to router. And finally Access points will be connected. Please suggest:...

ev4ld by Frequent Visitor
  • 1927 Views
  • 9 replies
  • 0 Helpful votes

ISSU is supported only within and between major releases, for example, 17.3.x to 17.3.y, 17.6.x to 17.6.y (within a major release) and 17.3.x to 17.6.x, 17.3.x to 17.9.x (among major releases), that is, for two releases after the current supported re...

Hi All, I'm currently planning a migration from a Cisco 5508 WLC with 3700/3800 access points to a Cisco 9800 WLC with 9100 series access points. Due to various requirements and constraints, the customer does not want to change the SSID names, authen...

dm2020 by Level 5
  • 4056 Views
  • 5 replies
  • 5 Helpful votes

HI, My costumer has a guest WLAN with web authentication and local user database configured by lobbyadmin. He would like to log to a syslog each time a gust user authenticates. On release 8.5 via syslog he could receive many logs and filter them by s...

l.buschi by Level 5
  • 548 Views
  • 1 replies
  • 0 Helpful votes

Hi there,We started using CBS350 switches for our customers. As my co-workers do not have a lof of experience with networking i am writing manuals gow to create VLANs for example. I would like that my co-workers use the GUI and not the CLI, becuase t...

qukolhavi by Community Member
  • 460 Views
  • 1 replies
  • 0 Helpful votes

I am trying to reset a 1572 EAP but reinstalls the same flash file again and again.Procedure followed by me was:1)Press the reset button of 1572 EAP.2)Power on the 1572 AP and wait for 20 seconds. But its flash file never gets' erased.Kindly let me k...

nikhilpandey by Frequent Visitor
  • 1064 Views
  • 1 replies
  • 0 Helpful votes

Hi,I have a problem with a guest portal using ISE. The portal is set up as a hotspot page and everything looks to be working fine - User Acceptance page is displayed and after you ok this you successfully connect to the guest wifi. However (and this ...

delpo40 by Frequent Visitor
  • 679 Views
  • 0 replies
  • 0 Helpful votes

Resolved! WLC 5508

Dear all,     How can i bind ip address to the respective mac address of a PC in a dhcp enabled network through WLC 5508 ?  

We found a couple of old 1141N AP's in our network that were not associated with the controller. Upon investigation I found that the MIC had expired. We are currently running 8.3.133 on the controllers. If this command is used in the shot term, (unti...

daswann by Level 2
  • 37620 Views
  • 8 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card