Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
We are deploying a few 9130AX with eWLC and we noticed an issue.In a network with multiple 9130AX/eWLC, one AP would be elected as Primary WLC, another AP would be elected as Secondary WLC. What we noticed is that, if the CAPWAP is IPv6, the AP Prima...
Hello, I'm looking at our 9800 WLC & trying to find a way to re-scan all of our AP's so that they can automatically adjust their transmit power. I recall when it was deployed that this was done, but can't locate the option again. Does anyone recall w...
Hello,We've been testing the new Entra ID feature on the splash page, and it's working well - the setup is straightforward and connections are reliable.However, we've encountered a limitation with the splash frequency configuration. When setting the ...
You're always a great help.The 5GHZ channel adjustment is automatic and automatically adjusted once a day starting at 0 o'clock.Six wireless APs (CW9166) were installed on one floor of the building (4F), but the next day, we received a notification f...
Ok guys so i noticed on all the wave 2+ APs cisco are now using the U-boot bootloader and documentation for it is little to none. I have a good amount of experience recovering and restoring APs. When i deploy APs for clients i prefer to format the fl...
Dears,I am experiencing a significant issue with the Cisco Access Point model 'AIR-AP3802I-B-K9,' where certain devices are unexpectedly disconnecting. When attempting to reconnect, the error message 'Cannot connect to this network' appears on Window...
A few weeks ago, I updated several AP networks including MR86, MR56, and MR models to firmware version MR 31.1.7.1. After the update, the APs began experiencing issues with radio transmit power on both the 2.4 GHz and 5 GHz bands. The transmit power ...
I am in need of the mounting dimensions for CW-MNT-ART2-00 in order to mount on light poles, I can find no schematics for this product.
Hello all,we recently received 2x Cisco C9124AXE and we need to use them for a point-to-point wireless bridge between two buildings as shown in the image. How can we configure them? They are brand new, I didn't convert them to any mode or EWC... I am...
Resolved! Rebbot on cisco AIR-AP1852I-N-K9 ARMv7
Hello there firts time posting here.I have a AP cisco AIR-AP1852I-N-K9 that constantly reboots, went it boots the led stay in green but after a wile it changes to amber,red and green then it reboot. I apply a factory reset to the AP and then I config...
Hello, I have a Cisco 9800 running mostly 9120 AP's, but recently we started getting 9164's. With that said, I have created an SSID for testing and enabled the 6ghz band. In my testing, the overall performance has been improved and hadnt run into any...
Hello team! I'm working on EWC 9120 for a requirement to implement P2P and isolate lateral traffic from users on an SSID. For a Tanium application, this option isn't valid, so the best option is to use ACLs. However, applying the ACL blocks all tra...
Hola comunidad,Estoy intentando actualizar mi AP Cisco 3802i-A-K9 con la imagen ap3g3-k9w8-tar.17_16_0_88. He intentado cargarla desde U-Boot con dos configuraciones distintas, pero en ambas se queda colgado al escribir en NAND.Primera configuración:...
Hi Meraki Team, I'm Sam, one of your clients, and would like to know if there is a possibility/ an option to push the Firmware upgrade for single AP from the network group.Recently, we have got the suggestion from Meraki dashboard saying to update fr...
Resolved! WGB without switch on the MAP side
I have a case where MAP simply connects single Ethernet endpoint to LAN.Thus technically i'd need wireless link to adopt mgmt VLAN to manage MAP & VLAN for endpoint.I'd then just connect endpoint to MAP's G0 configured as untagged in endpoint's VLAN....
