Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi, I am installing a 3504 WLC . The WLC is located at Brazil and the RADIUS servers are at Australia. Can some one tell what should be the maximum TTL between the WLC and the RADIUS server as part of cisco's best practice? Also is there is any guid...
Hi all,I have an 1832i access point connected to a 3504 controller. Everything had been working fine with it, but now the access point has gone a bit haywire. The LED is cycling through red/amber/green and it is not showing up under the "All APs" m...
Hi, I have a vwlc with 300 AP and 120 WLAN with different AP Groups.Now I have created a new AP Groups with 3 wlan and associated to 10 AP in flexconnect. I need to remove 1st and 3rd wlan on a single AP (keep the 2nd).How can I do ? Thanks
Hi, is there any way to configure a failover between 2 routers connected to a switch?I have a Cisco switch which has some VLANS, I´ve already configured subnets and pools in both routers, but both routers are giving IP addresses to each VLAN (giving ...
Hello friends, I tried to join a Cisco 2802i AP to a 5508 WLC but found an issue that is not allowing it joining successfully. I believe the problem occurs in capwap / dtls handshake (CAPWAP State "Configure"). Some details:. We have 170 sites. We ha...
How many SSID can i enable simultanously in a wireless network Embedded 9120 CISCO AP?Only can i enable one
Resolved! Cisco 9120AXi -E Boot loop
I now have 2 Cisco 9120AXi -E that does a Boot loop. I can come in to U-boot but thats it. Hard Reset doesn't help. Is there anyone who has had this problem and solved it?
Any help on this trap message? Any setting i can look for AP 'AP39', MAC: 58:bc:27:3a:fc:00 disassociated previously due to Link Failure. Uptime: 0 days, 16 h 08 m 18 s . Reason: Capwap WTP Event request. Thanks Mike
Server Information for LDAP================================Server name :LDAPServer Address :10.3.140.231Server listening Port :389Bind Root-dn :Cn=XXXXX,OU=XXX,DC=XXX,DC=comServer mode :Secure-TLSCipher Suite :0x00Authentication Seq :Bind/Compare pas...
Resolved! Cat 9800 RLAN-Local Switching AP1815T
I am trying to configure RLAN in 9800 with AP1815T without central switching or central DHCP.The AP and the controller are in the same LAN, so I use the AP1815T as normal AP in local modeI need a client connected using one of the three lan ports in t...
We purchased four 2802i aps. Since the maximum supported power of the switch is only 15.4w, we bought 4 poe injectors (AIR-PWRINJ6).The strange thing is that when I look at the controller, the ap status is still medium power (15.4w). And the radio ca...
Resolved! Access point cisco air-cap2702i-a-k9
Hi, I have 2 of the access point Cisco air-CAP2702i-A-k9 working fine, So I bought a third one. Can someone please tell me how to copy the configuration from the once I have and paste it in new one? Thank you!
Resolved! Convert ewc to capwap, ap_name issue
Hello,I have an error when I am trying to convert an EWC to a CAPWAP.WLC#wireless ewc-ap ap ap-type ap01 capwap % Error: no ap_name existsPlease can you tell me what am I doing wrong ?Thank youJ. edit : I tried to factory default EWC, I tried to set...
Hello. I have support for Cisco C9120AX and AIR-AP1852E.The problem is, in the local network there is already an AP1852E with Mobility Express configured as Controller - 1pc.I purchased 3 pieces of C9120AX AP with Cisco Embedded Wireless Controller o...
New to questions here. I have a foreign WLC that has guest wifi with the anchor in the DMZ. If I am trying to add a second guest WLAN, is there something specific I need to do? The original guest uses the mgmt interface (not recommended) and I create...
