Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
we have in office multiple switches but the POE connecting to the Cisco Aironet 1832i is a Cisco Catalyst 2960s-48, all was working with little problems / disruption until recently a lot of problems began to show connecting to Wi-Fi for several users...
Hello community, I have an issue with access points IP addresses. I have configured APs with static IP addresses but when I connected the APs to the switch they get an IP address from the DHCP in a different subnet than the vlan APs (because the swit...
Is it just me or is the Cisco CBW 140ac the worst access point? I have a 2 story house and a 140ac(Primary) on 1 floor and a 145ac on the top floor with mesh turned on. The problem with mine is that the coverage is very spotty/flak. If i turn one ...
Resolved! Change Meraki Email
Hi,We're implementing a guest SSID which will use Meraki Authentication. We're testing now and want to amend the email which users receive. I've looked on the dashboard but can't see where it would be set. Anyone know if this is possible? Even if we ...
Hi All, I wonder if you can help us with a Radius server failover configuration on our virtual 9800-CL. Specifically the 'automate-tester' command on the first Radius Server (ISE): !radius server 1address ipv4 1.1.1.1 auth-port 1812 acct-port 1813au...
Hello Techies, Need help, actually my client want to enable 802.1x security in SSID of standalone Access point for certificate base authentication, we do have radius server in our environment, please help me with the full configuration commands inclu...
Resolved! AP monitoring
Hello everybody!WLC 5508 controllerPlease advize how to more competently monitor a specific access point for falling off clients and establish this with the cause of the failure.Sometimes clients fall off a specific AP, there is an assumption that a ...
Hi, The below is part of output of show run of C9800 wlc . What is that meaning with packages.conf ? Is this normal?Thanks WLC#show running | i bootboot-start-markerboot system bootflash:packages.conf:C9800-L-universalk9_wlc.17.05.01.SPA.binboot-end...
I have a prime 3.x.Is it possible to create a job to execute certain specific "shows" and store them in the prime ???
I accidentally disabled the Network user and Management for a Radius Authentication server and now I am unable to log into the GUI. How can I enable through CLI? I am able to connect to the CLI via the service port but do not know what commands to ru...
hi everyone !i wanted to change the 802.1x password but the text_ (security onggle on wlan) bar does not exist on the wlc 2504 GUI !is there a command to change the 802.1x password on the 2504 wlc version 8.3 ?best regards !
Resolved! Can we check AP up time via C9800 wlc?
hi In old system wlc, we can easily check and know how long APs are online. In C9800, looks like we cannot find the APs up time. Maybe I could not find it. how do you think about it? Thank you
Hello One of our clients has WAP 561 (fw 1.0.3.4).Latest fw one is 1.2.1.7. Has anyone got any idea can I just upgrade it to the latest one or thee is path I need to follow?I wasnt able to find any documents in regards to that. Will appreciate any th...
hallo I have one Cisco Cisco LAP CAP 1142N-E-K9 access point. i want to access Web interface of Access point but i have a problem. i have one error message '''the AP in not in Flexconnect mode'.'i had tried top find out how can change AP mode from l...
Hi Team, We have wlc's deployed in sso mode. Tried changing the hostname of the primary(active wlc) and it got changed. But the secondary wlc still reflecting the old host name. Please suggest how to change the secondary (passive wlc) hostname. Regar...
