Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! same ssl cert on multiple controllers
can this be done? i have 2 controllers with expired certs and would like to save money buy purchasing only one certificate. the information i'm finding is conflicting. our systems were originally built by contractors so i'm not sure how they did ...
Hello!With the improved wireless health screens, I've been trying to diagnose some issues. I am seeing a lot of authentication errors (mainly with iPhone / iPads). Some are static and some roam from one AP to another. I've cleared the network setting...
Hi all, I have a problem with my APs not joining the WLCs. I am trying to connect my physical AP 1832I-E-K9 to the ISE sandbox lab in the dCloud through the Internet. I also tried to connect different AP (OEAP 1815t) to my company's wlc.. Same result...
Hi board,two quick questions: 1.) Is there a command to remove written tags from APs?So the opposite of the commandap name myAP write tag-configI don't want to factory reset the AP. I just want to remove the stored tag names from the APs 2.) Is there...
I've purchased a 3 pack of the Cisco Business 240AC access points and have configured them to the point where they work perfectly. I have a gigabit internet line and I achieve almost 600mbit speeds through WiFi so good start so far. After a few days ...
Hello,I have an AP 2802i that worked perfectly until was rebooted and now is not booting.I did found the bug "CSCuy03596" , but no solution for.I cannot request replacement because of missing contract support for APs.Do you have a solution for updati...
Hi Guys, We have faced hardware failure on our wireless controller, but we have GUI backup.Need to know what is the procedure to upload GUI backup to new fresh Wireless controller box. Model: - AIR-CT2504-K9 Awaiting your valuable support.
We have a WLC2504 version 8.2.141.0 with 20 AIR-CAP1702I-A-K9 and AIR-AP1832I-A-K9, the Vlan is default in the networkFor two years I worked well then, nest stopped being recognized little by little, now I don't see any of them, it's not a network pr...
I've done a factory reset (> 5 sec. push on factory reset button) on an MR-52 AP, but it's not broadcasting any of the default SSID's described here.The AP 's status LED is cycling through rainbow like colors and also blinking orange in between the c...
in 5ghz ,there is no channel overlapping so we can combine channel and make it as 40 MHZ or we can keep it as single channel also so what is rule about channel width?means when to combine or keep it as individual
Resolved! My AP MR33 doesn't Work
Hello Everyboby, My issue is below, I have 10 Meraki Access points that had worked correctely since 2 years ( i have license 3-years term). Now i have only 9 which work and the 10th AP is " Unreachable for 14 jours"* The network configuration is corr...
Can Prime be used to take the sh run config backup of Cisco Switch and Routers ?My Prime version is 3.1.
Hello I have a bunch of Cisco external antenna AIR-ANT25137NP-R attached to 3602E APs - the antenna has a 2.4 GHz gain of 13 dBi but I am unable to set this high gain on a WLC 5508 running 8.5.151.0 - when I set the value to 26 (because 26 * 0.5 dB...
Cisco IOS XE 软件，版本 16.12.04a思科 C9800-LF-K9Web 配置向导无法进行下一步。
Resolved! MR36 AP- Error message
I have placed 2 AP at site which is bounded to the template. It is working fine but sometimes its dropped from the internet. error message: Connection to the Cisco Meraki Cloud is using the backup Cloud connection.
