Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi all,We’re testing the new Meraki Campus Gateway and looking at Wi-Fi Personal Network (WPN) in combination with iPSK without RADIUS.When attempting to use Tunnelled mode to the CG, we receive the following error message "Bridge mode is required be...
I have a network in Gibralta and one in India. 6GHz is legal in both regulatory domains but is missing from the RF profiles.When will this be enabled? Have been waiting since April for Gibralta when the network was installed and I think 6GHz was deli...
Hello Cisco WLAN experts,being relatively new on the new 9800-WLC-platform, I noticed recently that AP outages are not recognized on the 9800-WLC running 17.9.3-code. The missing AP is a AIR-AP3802I-E-K9 for example.I cannot see any information abou...
I am trying to change AP mode from local to bridge ( via WLC GUI) but it won't let me. I see Warning: Changing the AP mode will cause AP to reboot but nothing happens. AP does not even reboot when I click Update & Apply to Device. WLC IOS version - 1...
Buen día, Tengo el siguiente inconveniente. Se creo un SSID con autenticación con Portal Cautivo para la conexión de usuarios a través de LDAP, este portal se despliega con ISE y dependiendo el employeType en el LDAP lo asigna a un SGT creado en SD-A...
New firmware release notes.Important noteWi-Fi 5 Wave 2 MRs support - This version and subsequent MR 31.x.x are only supported on 802.11ax (Wi-Fi 6) and newer MR models. 802.11ac Wave 2 and older products will upgrade to the backup version (MR 30.7.1...
We are looking to implement a zero trust through ThreatLocker and therefore we would like to find out which ports on the WLC need to be able to communicate with our domain controllers, our radius server, and with the APs. I have already looked at the...
Currently, the site is operating on 2802/3802 Mobile Express, but they want to change the SSH port from number 22 to another number. When I look at the AP's settings, I think it's impossible, is it possible? Also, if it's impossible, is there an offi...
お世話になっております。WLC9800-40(17.15.2)を利用しているのですが、MACアドレスフィルタリングに登録していたはずのMACアドレスが消えていました(すべてではなく1つのMACアドレスのみです)認証ログからおおよその日時を特定したのですが、休日帯であり、WLCは一切操作しておりません。原因が分かる方・同様の事象に遭われた方いらっしゃいますか？
Hello,two years ago I described a ROMMON and Ethernet Phy Upgrade on our 9800-L-C HA-Bundle.https://community.cisco.com/t5/wireless/9800-l-c-in-ha-rommon-and-ethernet-phy-upgrade/m-p/4996695#M265310Today, in preparation for a SW-Upgrade, to my surpr...
Has the 150ax been abandoned? The current firmware is 10.6.2.0 from 2023. The 140/145 have 10.10 from 2024.I find it hard to believe there's been nothing worth patching in two years.
Hi,We have two SSID's, one corporate SSID with 8021x(EAP-TLS) and the second is Guest SSID anchored back to DMZ.This is standard configuration present at around 1000 sites.Company phones are managed by MDM and connect to corporate SSID doing EAP-TLS,...
Is there any way to restrict the bandwidth usage Guest wireless users in Cisco DNAC. any pointers to configuration example or article will be good. If it is not possible in DNAC, can we achieve this in WLC.
Hello team, I have some weird problem on few access points connected to L3 switch. This is situation: L3 switch is DHCP for few access points connected directly to it. ip dhcp pool VLAN75_WIFI_MGMTnetwork 10.2.75.0 255.255.255.0default-router 10.2.75...
Hi everyone, As the title said, we just purchased 9163E-E and attached them to our WLC 9800 but their operationnal status are still down. For the record, we had to upgrade our WLC to 17.12.5 to avoid any compatibility mismatch. Now the AP have joined...
