Hi there, i got a cisco 2504 WLC with OS version - 7.0.112.56. when i tried to upgrade it to new OS , it gives below error. (Cisco Controller) >transfer download start Mode............................................. TFTP Data Type.....................
Hello.It's possible use 2 WLC 5508 en ANCHOR MODE in a Active-Active scenario?.For example, if one WLC get down of service, the other one keep provide service to the anchor clients?.In this moment we have just one WLC 5508 in Anchor Mode. What i need...
Hello Experts, i had converted a 9120 ap into embedded 9800 WLC using https://www.cisco.com/c/en/us/support/docs/wireless/embedded-wireless-controller-on-catalyst-access-points/215303-embedded-wireless-controller-conversion.html but after doing when...
We have 6 WLCs 3 on two of our major locations running 8.3.150 software version. We will be replacing our wireless gear so we will not be updating these WLCs and we are changing vendors. We will not be upgrading the gear until probably at the end of ...
Hello,is there a enabled "HREAP Local Switching: and enabled option "Learn Client ip address" on WLC can be a problem for static ip addresses on client?we have problem with wireless connection for Android devicesPoint is that we must have static IP a...
Hi, AP3602i cannot join WLC3504. Anyone can help to take a look at the below messages. Thank you [*04/12/2021 15:46:59.6862] CAPWAP State: Discovery[*04/12/2021 15:46:59.6885] Discovery Request sent to 10.10.10.3, discovery type STATIC_CONFIG(1)[*04/...
Our end-users are using MacBook, iPad(iOS), AppleTV, air-print enabled printer and etc. So we are trying to use Airplay for screen mirroring and Airprint for printing. Of course, service providers and requesters can be in different vlan. But we hav...
Good Morning, I'm attempting to setup a Guest WiFi. There is already a "Guest" SSID on the WLC. I believe it's a direct copy of the internal private SSID. Both SSID's are on the "management" interface. I'm trying to separate it from the internal...
AP 1810 moved to admin disables status after reload. Controller model : 5520Version: 8.5.161.0
Hello, Two dynamic interfaces are created at the WLC and Switch. DHCP server is located at the switch for vlan10(Guest) and vlan20(for internal client). My question is if the port f0/9 has to be trunk? Configuring it as access mode cannot work for th...
I'm familiar with autonomous APs but am new to the WLC. Is there a way to just bridge the WLAN traffic to a VLAN? I don't understand why the WLC requires an IP address for the VLAN when the clients essentially are already on that VLAN. How is it used...
Hello Everyone,Anyone have an experience with RF YAGNA Tool before or any video how to practice on it ,i am willing to purchase starter bundle since Basic bundle have limited features .
Hello,I have a question. vWLC 8.0 is installed at vmware workstation and then the ap3702 can join the vWLC, but if the same vWLC installed in ESXi6.7, the same ap cannot join the same vWLC at ESXi. I got the below message, some of them show “Bad cert...
Hello, Anyone can help to resolve the issue? AP3702 cannot join vWLC 8.5, Below is some info, with below message, why it has ip address 10.0.100.175, i did not assign the ipPlease let me know it if any info needed. Thank you AP: Invalid input detect...
Hello, I've setup an internal lab which uses the 9800 WLC (on AWS with a VPN to our lab). And now i'm trying to onboard an out of the box 2702i AP.The join process fails: CAPWAP DTLS session closed for AP, cause: DTLS handshake error* The AP is curre...
