Dear All,our 8540 wlc (Rel. 8.5.140.0) doesn't seem to support radsec. At least we haven't found any possibility to configure it. We only find a button to activate IPsec or to define a port (obviously UDP).Is it true that as of now the Cisco 8540 WLC...
Forum Posts
Hello Folks, I have a SSID with 802.1x PEAP as authentication metod, i want to know if there is some way or configuration on ISE to ask for the certificate on the client side. I want to configure that if you do not have the option to verify the certi...
Greetings , Can someone please share their knowledge and experience regarding solution/deployment of sms gateway for wireless controller for guest users of WLC to receive SMS notifications with login credentials etc? Is there any sms gateway soluti...
Guys, very basic question - how a client device shows single ssid when there are many aps installed? Example we have corp ssid and 10 aps in the floor. But our laptop/mobile shows only one SSID to connect (which means only one BSSID). on what basis? ...
Message: '802.11a/n' interface of AP 'abc' associated to controller 'xyz (192.168.1.10)' is down. Reason: Radio channel set.Failure Source: abc, Interface 802.11a/n WLC-- Model: AIR-CT5520-K9 Software version : 8.2.141.0 Prime-- Build - 3.1.0.0.1...
Good morning,if I'm right, i need to setup an ACL on Flexconnect groups to enable client isolation on a open wifi guest. Can you please guide me step by step ? Thank you.
When the WLC switches over only the Root Access Points (RAP) are staying in the network. The Mesh Access Points (MAP) dropoff the network and then join back. Is this an actual behavior? or the RAPs and MAPs should seamlessly join to the new Primary W...
hi,i would to control a capwap 702i with controller 5508, they are located in tow different network.the ap has join the controller but when i enable the wlan, no wlan appears.i'm using flex-connect technologythank your for event helps.
Resolved! 1111 WLAN Controller
Is it possible to turn off the status lights on wireless access points that are connected to the 1111 WLAN controller? I was looking for the option, but I do not see it listed. Thanks, Alex
I have problems: Access Point can't join to Wireless Controller[*07/07/2019 08:25:21.0000] CAPWAP State: DTLS Setup[*07/07/2019 08:25:21.0000] DTLS connection created sucessfully local_ip: 192.168.1.138 local_port: 5248 peer_ip: 192.168.1.10 peer_por...
Resolved! Cisco 3504 Wireless Controller
Dears I have a Cisco 3504 wireless controller and old Cisco AIR-CAP2702i-E-K9 access points. I want to know is that access points can support Cisco 3504 Wireless Lan Controller. Shajan
Resolved! Cast across vlans wired or wireless
Hello Team,Our team has been tasked with creating a vlan to allow wireless or wired devices to cast to our ClearTouch panels that would either be wired or wireless. I want to be able to cast from a wireless or wired device with the software we use. H...
Hi, we are running with wireless controller which getting closer end of life, and so, plan to refresh with new wireless controller. what I'm thinking to replace it simple(retain all the IP info as possible) and safely. I have in mind to install anoth...
When logged into the Cisco GUI for one of my 6 Aironet 2600's whenever I attempt to make a change in the Server Manager it redirects to an unavailable web page (HTTP 400). This happens whenever I attempt to Delete a RADIUS server from the server list...
I am working on a WLC and I want to control timeout function with an external web page, but I can't find anything to control the timeout through a web page. Is this possible and if so what is the function. I'm looking for something like this but with...
