Hi, I'm trying to set up a new AP on a 5500 WLC and the WLC is able to see the AP but the AP fails at downloading a required image and is looping trying to get the image to download. A snippet of the CLI output with the error is below. Thanks! *Feb 1...
Forum Posts
Hello EveryoneI have a C9115 that i converted to EWC Using ap-type mobility-express tftp://10.1.202.111/9100/ap1g7 tftp://10.1.202.111/9100/C9800-AP-iosxe-wlc.bin The device came back up in recovery mode and i tried installing the binary using this c...
Hi there to all!I've configured some yeas ago 4x AP-1832i with ME firmware, so there is a virtual controller.Exact model is AIR-AP1832I-E-K9 ,and firmware version is: 8.5.120.0.Now i've some problem with web manage page, everytime it put me out and a...
Resolved! Can't join 2702i to C9800-CL WLC
Hello all,I have setup a C9800-CL controller for a lab environment but am having problems joining a 2702i access point to it. This AP was previously joined to a 5508 WLC running an 8.5 image. I have researched this issue and came across numerous po...
Hi, We are migrating from AiroS controllers to 9800 platform.In AirOS we used to give two types of access to Admin users using role supplied from ISE. 1.FULL2. MONITOR Now we want similar thing in 9800, which is IOS XE. In our environment we have a ...
Hi i All, Just wanted to know if i disable finger service on WLC, will be there any impact also how can i filter and drop half-open connections? thanks in advance
Hello I have On site a cluster of WLC 5508+HAand it works with iOS 8.5.161now I have another new cluster of WLC 3504+HA of iOS 8.10 and need to do mobility group between both clustersI read that we can do mobility group of different IOS but will have...
Hello I have a conjuration that could not have been done without the assistance of Tyson Joachims and it works perfect. What I want to do now is "phase 2" of my config and it was mentioned that ideally I would set up the other 2 AP's via PoE and have...
Resolved! Cisco AP 1832I not upgrading to ME
I have an Access Point AIR-AP1832I-E-K9I'm trying to do the upgrade to ME but when I start the process:ap-type mobility-express tftp://XXX.XXX.XXX.X/AIR-AP1830-K9-8-5-151-0.tarStarting the ME image download...It may take a few minutes to finish downl...
1832i-D-K9 AP not joining to WLC 2504Getting AP CLI errors as below [*02/03/2021 15:13:25.6645] CAPWAP State: Discovery[*02/03/2021 15:13:25.6645] Discovery Request sent to 192.168.0.73, discovery type STATIC_CONFIG(1)[*02/03/2021 15:13:25.6645] Dis...
Hello, I noticed on my EWC, CleanAir's statistics are empty (monitoring -> wireless -> CleanAir Statistics) even if cleanair is enabled on my EWC (Configuration -> Radio Configurations -> CleanAir) on both frequency 5Ghz & 2.4Ghz. Why CleanAir stati...
Hello, We have 2 APs, one 3802I and one 3802E on a site, these are flexconnect APs connected to a remote WLC 5520.They were facing issues in 5Ghz, changing often channels, and channel width (Best in RF settings), so we decided to configure them with ...
Hello, We've been having some issues with multiple devices that are being deauthenticated with ReasonCode: 108. The devices either auth using certificates, or PEAP username and pass, and on either type of authentication the WLC has log entries throwi...
Dear all, I have some AP AIR-AP1832I-E-K9. One of this is configured as Primary and master controller and all others are configured as AP ME Capable. I have configured a new Vlan (for mobile devices) and configured for this, a DHCP pool server using...
Resolved! 802.11 Clients Communication
Dears,I have started to study wireless and there are some concepts confuses me What i Understand is that the client will obtain an IP like this way:--The client will send a DHCP request over the AIR to the AP , the AP will now send this data over c...
