HiI'm trying to set up my two C9800-L-F controllers with redundancy using RMI+RP, but I find the use of IP addresses confusing. I have given each box 2 IP addresses so far:Management:Controller1:interface GigabitEthernet0vrf forwarding Mgmt-intfip ad...
Forum Posts
Resolved! Client debug - connecting issue
Hi all,I ran into a problem with one of our sites. Corporate clients are using 802.1x for authentication. Problem is that clients can't connect on wifi. I first thought that problem is with DHCP and not getting IP address, but it might be authenticat...
Hi Team,, Actually I have a query about below one point in WLC HA-•" A Redundancy VLAN should be a Layer 2 VLAN dedicated for the HA Pairing process. It shouldnot be spanned across networks and should not have any Layer 3 SVI interface. No data VLANs...
What's the process to do a factory rest on a 9120 AP via CLI? I'm not finding any commands that work on this model. It is running 17.3.2a code.
Hi,Does it possible register a Lightweight AP to remote Controller that are comunicated through a VPN site to site?best regards
Hello, Issue: I have 3 WLANs configured on a WLC with separate VLAN(100,101,150) for each. Also there is a management VLAN(100) which does not have WLAN created for it. When clients associate to Lightweight APs, they receive IP addresses which are pa...
I have an odd problem, wondering if someone has seen it I have an 1832i that was in capwap mode. I was converting to ME and after that things went down hill. The 1832i sli was working hence I was able to login and point it to the tftp server to down...
Hi all,Let say i have 3 WLANs, with 3 different SSIDs. CORP-ssid for employees laptops, CORP-mobile for employees phones and guest-ssid for guest. If I have 10Mbps internet link, is it possible to set some limitations on those WLANs, so that CORP-ssi...
Hi there, Trying to connect a Google Home Mini to Guest WIFI SSID and no luck. I was able to connect an Amazon Echo but not Google Home Mini.
Resolved! MA Ant 20 Dual Band Installation slots
Hi,We have MR74 Access Points, which consists of 4 N-Type connectors 2 each for 2.4 GHz and 5 GHz. I am confused as to which slot should we install the antennae on; If need to install 2 Antennae on an AP, should we consider 2.4 slot or 5 Slot?What if...
Resolved! Getting started with WLC and Mesh
Given the current "situation" in the world, most of us are now working from home. I needed a more reliable WiFi implementation in my house to support the 5 of use (wireless laptops, cells phones, IOT devices, video streaming etc). Frankly I got tire...
Hi all,I have two MR36, one as mesh and the other one as gateway connected to an MX68 in routed mode. MX250 is in VPN Concentrator mode. Vlan 1 is defined as in VPN, Vlan 2 is for local breakout and Vlan 3 is for management (Native Vlan in trunk inte...
Cisco Access point not able to join the 8500 WLC Port on switch does not come up Access point gets power from 3850 switch however the interface does not come up IOS Bootloader - Starting system.flash is writableAntigua Lite Board P240MB formatTide ...
Hi, I am installing a 3504 WLC . The WLC is located at Brazil and the RADIUS servers are at Australia. Can some one tell what should be the maximum TTL between the WLC and the RADIUS server as part of cisco's best practice? Also is there is any guid...
Resolved! Content filtering on WLAN vs LAN
If I have a Wireless LAN SSID that connects to the same ip range/vlan as the LAN subnet, do the LAN rules, specificly, content filtering, apply? Basically, if I blacklist a URL on a device that has both LAN and WLAN, does it block both, or do I need ...
