Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Dual-band patch antenna on MR76
Hi, I wonder if it would be enough to add one MA-ANT-25 to a MR76 AP to run both 2.4 and 5 band. The MA-ANT-25 has two connectors, one for the 2.4 and one for the 5 band.What would the implication be if I choose to only use either the vertical or hor...
Hello, I would like to connect 100 to 5000 embedded devices that use ESP32's WiFi connectivity to a server. ESP32 is 802.11b/g/n capable in the 2.4GHz band. Could someone please recommend an Access Point network solution for high reliability ( 0 disc...
I've desperately tried understanding the licensing of the AP in the 9100 series without success. I need a new AP for use in a home office. Nothing special but it needs to support Wifi 6 with AX and WPA3. I also need support for at least 9 SSIDs with ...
Hello. - Topology - WLC - L3SW - RAP - MAP - L2 - PC RAP - MAP Check. Checking the signal quality the 'Show mesh ap tree' command.Check the SNR value.I have a question among them. 1.Chan Util- When there is no traffic, it is 10%, and when there is a ...
We got a report of sporadic wireless client connectivity drops in the last week.Checking the logs it was discovered that at least back to Aug 8th we were getting this:%DOT1X-3-ABORT_AUTH: [SA]1x_bauth_sm.c:487 Authentication Aborted for client <MACAD...
I am setting up my first MSE and accidentally selected presence instead of location during configuration. I want to either factory reset the device and start over or have the ability to change from presence to location. During the cassandra configura...
Resolved! Debug Flexconnect
Hi All I've recently upgraded from 8.5.161.0 to 8.10.130.0 on my WLC 5520. All my APs are in local mode, but one (2802i), which is in Flexconnect Central switching. That AP has OEAP enabled. For whatever reason, the clients at that remote location ca...
Dear all, I have an AP AIR-AP1572EAC and wanted to reset to default but all times I try to reset it, it competely does not get to the default. I unplug the power cable and press the reset buton and connect the Power cable back, and the LEDs would tur...
Hi, I have seen this behavior on other users macbooks as well. When Anyconnect version changes keychain prompts for password 3x and providing the user enters the correct pw 3x it goes away. From researching this it appears to be related to one or mor...
Hello, I am in trouble with WLC Controller 5520.The issue is related to reading the system info information from the ssh console.For example, on Tuesday the WLC Controller is rebooted of a software crash reason.When we log in a few minutes later and ...
I newly bought some APs for few zones(inside only) in the warehouse.The AP model is 'Aironet 1852E', and this series can have antenna up to 4.The height of warehouse is quite high (=around 15ft), so I bought some cables too. (50ft, 100ft) Now, the p...
(Sorry for bad English)Hello, We have a WLC 5508 with the system version 8.5.151.0. On that WLC we have 3 types of AP associated : - Access point 1532- Access point 2602- Access point 2802Last week all of 2802 lose the association with the WLC, and i...
Hello Experts, Is there any means to get the power that an Access Point is drawing from the switch?Rather than Full power if there are means to obtain the exact power that would serve my purpose. Running into a situation wherein IW3700 as light weigh...
Resolved! One question about MR20...
normaly we use MR33 in our network. Now, our customer needs an AP very simple, no-frills, no wids,.... but cheap ! Does anybody know when the MR20 was launched ? Is it reasonable to deploy these APs or is EOL in sight ?
I hope someone can tell me what I need to do to provision my 1852i. My goal is to set this device up as the Primary AP on my network and my problem started when I couldn't access the Mobility express web console. I tried resetting the access point,...
