Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Thanks for your help!I'd like to know if I can clear all DHCP leases in just one WLAN through the Wireless LAN Controller. Regards.
Hello to all,I have a WLC Cisco 25series an many access points. Suddenly we face an issue with airprint wirh a Xerox Device, probably bacause of of Mdns configuration. Can you help me to find the reason i 'am not able to print even if the print is sh...
As we have 9200L-24P-L which have 600w power supply and as per update we should not exceed 80% of that while connecting Ap.So if I have 30 watt power required AP then I can connect only max 16 AP to this switch as I can use 480 watt onlyPlease let me...
I'm trying to configure an autonomous 1142 as a work group bridge, to hook up to a printer that doesn't have a wireless card. The SSID I'm trying to connect to, uses WPA2 Enterprise, 802.1x+CCKM, PEAP username and password authentication. How do I co...
I'm working on setting up the Cisco vWLC controller as Hyper-V VM. I've downloaded the ISO, MFG_CTVM_LARGE_8.5.161.0.iso, and believe that I've followed the Hyper-V setup guide correctly but the controller doesn't boot up - it shows an error"Starting...
We've one instalation with a Mobility Express (AIR-AP1852I-E-K9C) working with two AIR-AP1852I-E-K9 (Software 8-3-133-0 in the three cases). Recently we bought a new CAPWAP (AIR-AP1852I-E-K9) and we put the software 8-3-133-0 but can't connect with ...
Hi, I'm trying to joing a AIR-CAP2602I-E-K9 to my 1852i with mobility express. Regarding to https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8_4/b_cisco_mobility_express_8_4/b_Mobility_Express_Deployment_guide_chapter_0100.html th...
Hi team, What is the trick to enable AC and AX speeds on the 9130AXI-EWC? The CLI for 'ap dot11 5 dot11ac' indicates that A needs to be disabled first. Help says 'ap dot11 5 shutdown' will disable A, but as expected, shuts the whole radio off. Thank...
hi GuysI have a problem.I got a new MR33 and 4 new MR42e APs and should set them up.The APs are connected to a Cisco 2960 switch, switch port is configured as a trunk with Native VLAN 555.VLAN555 also assigns the IP address and comes on the Internet....
I have one of these and a couple of 1142 AP's that I would like to learn with.I've had this on a shelf for a long time now, and I pulled it off over the weekend and started taking a look at it again.I found that it is EOL and I cannot find anything o...
A client today was able to connect to the WLC via ap as normal. The user was then able to unauthenticated the device and connect to a spoofed SSID. What blocked him to go any further was PEAP to Cisco ISE. Question is, is there a setting within the...
I already tried ressetting and downgrade ap help me
we have 5200 controller with Config backup of this device. we need to migrate this to new 9800-L wireless controller. we have tried to convert backup from 9800 controller itself, it is showing translated config, unmapped and unsupported. require assi...
Hi Everyone,I have an AIR-CAP3502E-A-K9 with the autonomous (AP3G1-K9W7-M), Version 15.3(3)JF12, RELEASE SOFTWARE (fc1)All the CLI works as expected but the Web GUI give me a "404 not found error" anytime I press the Apply button to push a new config...
