Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi, My device with Version 15.3(3)JD, RELEASE and model No. AIR-CAP1702I-D-K9 I've logged into the device and enable http and https but when I login using the IP mentioned in the BVI. I get 404 error. Interface IP-Address OK? Method Status Proto...
Is it possible to run a mesh using Mobility Express on the 1830's or 1850's? Or is a controller required?
Hello All, I am looking for a clarification on the software update on the Mobility Express if we elect to not select the Auto Restart box. While, scheduling reboot and checking in the auto restart does boot the new APs and ME Controller with the new...
Hello, As you know lightweight APs can be configured in several special-purpose modes, one of them is the Monitor Mode which provide us rogue AP detection, but on the other hand we have Rogue Mode which seems to have the same ability ... so why would...
Greetings all,I have an 7 floor apartment building where many clients are being disconnected and reconnected repeatedly. These are client connections that start off as 2.4 GHz but bet bumped to 5 GHz and then go back. I have "Dual band operation with...
I have an older Air-Lap1252AG which is now showing a certificate failure. Looking to upgrade the firmware however I cannot find this model number in any of the wireless device download lists.
Hello, I cannot solve this message in the WLCCA platform 100004,AP: It is recommended that the FlexGroup and the AP have the same VLAN configuration. I have vWLC and Flexconnect AP Flexconnect group with native vlan configured Please help me
We have single WLC at site and 2 access point1st AP connected in local mode and mapped to AP group 12nd AP connected to same WLC in flex-connected mode and mapped to Flex-connect group 1(This AP is connected in warehouse area) Both AP in same physica...
Dear Experts, I tried looking at datasheets but couldnt find this info. Can someone tell me or point me to the document which specify the number of internal antennas for 2800 and 3800 APs?
HelloI am new to wireless and I got Cisco AIR-CAP3502I-A-K9 wireless access point and installed vWLC (version: 8.5.161.0) on ESXi.vWLC: management interface is bridged to outside and it is reached by switch and AP.AP: is POE from the switch, getting ...
Good day all got a troubleshooting question here I need to ask.I have received complaints from user connections dropping when using smart phones such as Apple and Android. The current AP they are using is an 1131 (to be replaced soon) however when I...
I try help my friend to upgrade his LAP1041N-C-K9H to Fat mode AP(k9w7). This K9H doesn't use C1140 fw, it use ap1g1 ,same as 702i.I try update the least K9w8 lwap mode fw to device, it look normal. But when I try convert it to fat mode K9w7 mode , i...
I'm using vWLC 8.5.161, The AP is AIR-OEAP1810-CRD. Another AP is working excellent. I try to add this AP. It's show joined. But it will be disconnect soon. The light flash red-green-orange. It's mean try to jion the WLC. And it jioned,then disconnec...
Hi,I was looking at the datasheet for the c1852E access-point, and i could just see one compatible patch antenna for this particular AP, AIR-ANT2566P4W-R=.I am looking for something with a narrower beamwidth. Is there such a thing available for use ...
as can be seen per pictures below it is possible, at least visible, to update radius accounting/authentication server via web interface but for command line there are no such command (totally delete radius accounting and create again is not an option...
