Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I have a 2504 and a 5508 controller that I am using for my certifications. I am trying to backup the files on the 2504 to a tftp server. The tftp server is running on a laptop that is connected to the network. I can ping from the laptop to the 2504 W...
Is there a way in Prime (3.2) to copy a template or create multiple lightweight access point templates without having to individually add a template? Such as a copy feature, or through an API?
Hello all. Does anyone know what Cisco’s solution is for wireless IPS now? I have a customer looking to detect brute force attempts against their wireless network or other true IDS/IPS attempts? They’re running 5520 wireless controllers with the 380...
Hi,I am having a weird issue that people are getting randonly disconnection or ip phone goes to registering but there is no disconnection on the wlc. the WLC logs show there is no disconnection when that happens. I think this is with regards to DCA w...
Hi, I have 3 WLAN in my Cisco Mobility Express and one SSID in each WLAN (total 3 SSID). All the SSID are in the same VLAN. Do you know if it is possible apply Client Isolation only in one WLAN? Thanks, Joan
Hello, i´m trying to deploy a new setup on our wireless network to connect a remote site on our WLC 5508. Due to some rules, we need to setup flexconnect Central Switching, all traffic via Capwap. APs are cisco AIR-AP2802I-Z-K9 This is our network t...
The 2504/3504 WLC supports 802.11k Beacon Reports (Active/Passive/Table), Link Measurement Reports, and Transmit Stream/Category Reports. I enabled these features in the WLC, and using Wireshark, I verified they were enabled in the 'RM Enabled Capab...
Hello, I have some Cisco 2800 APs (AP2802E) setup as Flex connect with a AIR-CTVM-K9. The problem I'm having is clients are dropping a lot of pings when it roams to a specific AP, CWA09P, I think my client is going through a full roam everytime it c...
Hi Guys,I have Cisco Prime 2.2 and WLC 8.3.122.0 and I added WLC in Cisco prime and is synchronized but no AP are added! what could be the reason?
Hello,Trying to convert an AIR-AP1815I-K9 access point from CAPWAP to ME, installation of a new image fails. IP adress assignement -> OKPinging with tftp server -> OK.tar image download -> reach 100% but stuck there. During the process, console outp...
Resolved! 9800-CL virtual WLC
Hi,I wanted to know if there is any Cisco documentation on a n+1 HA design where I have one vWLC in one DC and the second one in a diff DC geographically different. The vWLC in use will be a 9800-CL. In this scenario the mgmt ip will also be differen...
Dear Community, I need my 3850 switch works as a Wireless Controller but i am facing some problems. I have 2 3850 switches which are deployed on different location on a same office. I have 5 access points and need integrate with the wireless controll...
Hi,We are trying to deploy AIR-CAP3502I-A-K9 with 5508 controller. However the controller is back order and we don't want to delay our site survey. Can we use the AP in stand alone mode for the site survey? We don't need it to operate or pass traffic...
Hello,Since updating to firmware 25.14 on my MR33 ap's, my machines are connecting to access points nowhere near to them, e.g. they can be sat below an access point, less than 2 metres, but connect to another access point across the building with a v...
I found some trouble about Wifi internet cannot print out data but LAN can print.I use access point for CISCO WAP-150 and just update version of firmware to 1.1.1.0 on middle last week. but just found trouble on Monday. and for CORE SWITCH i use CISC...
