XR OS and Platforms

hello, we have problem in our ASR9001 Ver 4.3.4, after an accidental power off due electrical problem, led LC fail still red and line card (module and interface) not shown as active see here some output  RP/0/RSP0/CPU0:ASR9001-01#show platform Tue No...

Hello. In our company (ISP) we have 2 core routers (ASR9K) and 2 BRASes (ASR9K). One BRAS acts as a gateway for users to which are assigned NAT IP addresses and the other for users to which are assigned public IP addresses. I want to mention that the...

Hi all i want to change a router 7609 with a ASR9000; I enter configuration in the new router  and when i switch on , the STM4 card doesn't work. Below message error  LC/0/0/CPU0:Nov 14 23:26:13.729 : g_spa_0[206]: %L2-SONET_LOCAL-4-ALARM : SONET0/0...

Dear All,   As part of the SMU quality initiative, SMU testing team is seeking feedback regarding any SMU issues seen by you or your customers in the field. This is an effort to help improve quality of SMUs posted on CCO.    It might be install issue...

hello can anyone knows about this error: Thu Nov 10 16:07:01.222 CSTRP/0/RSP1/CPU0:9010-PE-MEX10(config)#int GigabitEthernet0/0/0/6.842RP/0/RSP1/CPU0:9010-PE-MEX10(config-subif)#SERVIce-policy OUtput 20-25-25-15_10M ? account Turn off layer specific ...

Hi,    I have a ME3800 that I'm migrating to an ASR 9006 running 5.3.3.  but I have not been able to find an alternative to migration config for a SVi with an xconnect for example: ip vrf TestVRFpseudowire-class Test encapsulation mplsinterface Vla...

Hi , i have Cisco 7206VXR NPE-G2 and ASR1002 working as LNS connected to Radius i need to use CoA or PoD to change the speed per l2tp user that i can do the following : 1. change the internet speed for ADSL customers during the day without hard disco...

Hello, I tried searching but couldn't find any solution regarding this, so I'll explain a little. I have an ASR9K series router setup to act as a PE device and on the other side is a JUNIPER ROUTER (let's say ISP) The ISP has given us 94.x.x.x/31 I...

  RP/0/RP0/CPU0:SZYQ.KT.HX00002F03_I(config-static-afi)#do sh route ipv4 multicast static Wed Nov  9 09:56:48.416 PRC % No matching routes found Dear Sir/madamhere is my problem//I config multicast on my network,multicast receiver under CRS-1 router/...

The SW download section for the 9910 is still missing, while the chassis is already out a long time: Yes, I am aware that the binaries are the same, but this is embarrassing for us to the customers. Fix it. Soon. Thank you

I have about 14 SMU that I need to activate on my ASR9010 (XR 5.3.3) due to a on going memory leak issue. About 4-5 of them is a reboot SMU while rest is hitless Just want to know, can I activate all 14 SMU in one go with one one reboot? If so, what ...

I just start to work with ASR 9000 and i'm used to branch router I need to upgrade ASR 9000 5.3.3 upgrade to code SP4. Do I need to do anything special?

What is the Roadmap for Cisco offering BFD/UDLD on the ASR 9000v Satellite Fabric Link?