Resolved! How to check ASR9k is 32bit or 64bit?
What is the command to see my ASR9k is runnung 32 or 64 bit?
What is the command to see my ASR9k is runnung 32 or 64 bit?
Hi team, After switching to a backup RSP board (on ASR903), using the backup forced switching method, it became impossible to connect to the router via the ssh protocol (telnet worked, ping went through, and all protocols functioned). After returning...
EVPN Convergence time in a Multi home setup is about 20 seconds. It's too slow.I have one CE connected to two PE1 and PE1.PE1 and PE1 are connected to the MPLS core. From MPLS core there is another PE3. I'm running an 10G RFCtest between the Custome...
Hi,is the 5th generation linecard A9K-4HG-FLEX-FC supported on the route switch processor A9K-RSP880-LT-SE in ASR9910 chassis with 3x SFC-S installed? This link says SFC-S is compatible with A9K-4HG and A9K-8HG linecards:https://www.cisco.com/c/en/us...
Hi Guys, I am seeing there are two different serial numbers for same PID on the "show inventory" comment in cisco ncs540. But only one serial number is covered under cisco support and other is unidentified. Please anyone can help me to understand wha...
Hello I would appreciate if you could help me with IOS XR SNMP. I use the Snmpwalk command to find the state OID for BGP sessions. When I run the command the session by in time-out? I use IOS XR version 5.3.4 snmpwalk -v 2c -c toto X.X.X.X or snm...
Hello, do you have experience with building GISO for NCS540 (XR7 platform)? I have tried gisobuild.py (version 0.38), but the script return errors. Thanks, Peter
Hello, We have a line card A9K-MOD400-TR which was inserted in a chassis 9910 and worked in version 7.1.3 (64bit) , we want to remove this card to another chassis with RSP880 in 32 bit version 6.1.4 . Due to some other second generation card in the s...
Hello.I have a setup like this:Where both sites are connected trough a bridge.The issue here is that the bundle is not load-balancing, the traffic is flowing only through one of the linksThe customer runs mpls between this two sites and on top pppoe....
Hello Community! I upgraded our NCS57C3 routers from 7.5.2 to 7.7.21 but after this the MPLS traffic is not load balanced between the links. NCS57C3 with 7.5.2 load balances the traffic perfectly but 7.7.21 - first link is exceeded, second and third ...
In IOS XR, every 20th commit XER is doing config rebase operation and it delays the commit. And if we terminate the ssh session while rebase operation is on-going, then the config which we commit will rollback.Is there a command (exec or bash) to for...
Hello all,we are planning an upgrade of our ASR9910 to new 64bit system. IN release notes there is a mention of bridge SMU CSCvw57276 required for this upgrade path. But there is a note that it is applicable for 64-bit systems.he following table outl...
Hi all, We are monitoring the ISIS Adjacency status on an ASR9k using SNMP. The issue appears when pooling the isisISAdjState for some of the entries in the table. For example, if we walk the table we see all the adjacencies and there corresponding i...
Hi Guys, I'd like to import specific prefix from VRF B (RT:65500:1000) to VRF TEST. I have the following config but it's not importing the specific prefix. If I configured import route-target 65500:1000 then I'll be receiving all the prefixes in that...
We have an ASR-9001 and it was running 5.1 and we attempted to turboboot unit to 6.4.1. Then this happened. RP/0/RSP0/CPU0:Apr 19 08:04:04.410 : cfgmgr-rp[158]: %MGBL-CONFIG-0-INIT_FAILURE : Configuration Manager was unable to initialize the Admin Co...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-22-2024 12:39 PM | ||
08-11-2024 09:12 PM | ||
08-07-2024 01:36 AM | ||
08-02-2024 01:20 PM | ||
06-28-2024 06:17 PM |
User | Count |
---|---|
1 | |
1 | |
1 | |
1 | |
1 |