Hello team,We are encountering an issue with the 100G TR card on the ASR9K, which presents complications wherein shutting down one of the 100G ports resulted in an automatic shutdown of both 100 ports. If fiber connection is disconnected from the fir...
Forum Posts
Hello everyone,I have a A9K-4X100GE-TR that has problems with the N. is there anybody has same experience and have any idea. RP/0/RSP0/CPU0:February(admin)#sh platformThu Feb 15 15:49:05.009 UTCNode Type State Config State----------------------------...
Resolved! Cisco ASR9006 bgp always idle
Hi,I can try to configure asr 9006 for bgp but I always see bgp neigbours idle. My configrations and asr logs are below. What can I do? Could you advice me please. ASR 9006 Router Config:!route-policy Accept-All pass end-policy!router bgp 100 bgp r...
Resolved! HELP - ASR-9001
I am fully aware that there are 2 versions of the 9001. 9001-S and 9001.Both 9001 and 9001-S have 4 built in SFP+ ports and BAY 0 and BAY 1.9001-S by default has BAY 0 active and SFP+ ports 0 & 1 active and requires a license to activate BAY 1 and S...
Hi,I want to reenable an older ASR Satellite, but all I get is "no Identification received yet" and a reboot every 30 minutes.Other satellites (with newer software) are working fine.Here is my ASR output and config (IOS cXR 6.6.3):sh nv sat statuSate...
Hi,in our network we're using the A9k-48x10-1G-SE LC on our ASR 9k deployment (running eXR 7.3.2), these boards have huge (in the thousands) l2transports interfaces configured on them and, most of these, have a service-policy associated. Is it possib...
hello everyone ,can a standalone Cisco ISR 4331 handle BGP ISP internet routes ?
Hi dears , we have a Cisco ISR 4331 with software version Fuji 16.8.1 , which have known vulnerabilities.we want to patch theses vulnerabilitieswhich version should we move to ? and what is the upgrade path?thank you in advice.
Hi All, I've a question on Multihop BFD protection on XR platforms. Multihop BFD (RFC 5883) packets are sent over UDP/IP. The encapsulation used is identical to single hop BFD (RFC 5881) except that the UDP destination port is set to 4784. Now, suppo...
Hello Guys,I have an AS9902 connection to a Nexus 9000v.On the Nexus i have configure a VNI and a VLAN association. I also have configure a peering with the ASR9k.On the ASR i have configure the EVPN VXLAN Layer 2 Data Center Interconnect Gateway. On...
Recently one of our contractors supplied catalyst 3850 switches to our site with irrelevant End customer. When we try to contact their supplier for changing the End customer details, they are reluctant to change. Please advise what is the procedur...
I would like to copy a file from sysadmin mode to normal mode but I don't know the commands to do. Please help me.from this mode: sysadmin-vm:0_RP0#to this mode: RP/0/RP0/CPU0:ios#
In this situation, my Router_A not established a IS-IS session witch other Router_B, and this is a information on interfaceThis is a network /30, ARP ok conectivity ok I apply a reboot on router, but not successfuly, I replaces with another network /...
Resolved! Flowspec RFC 5575 validation
Hi All,I was testing on an IOS-XRv image, to then put into production on a pair of NCS5508 flowspec routers. A question that arose me, is whether the route validation defined in RFC5575 can be turned on.A flow specification NLRI must be validated suc...
Resolved! Configuring ePBR on the NCS540
Hi team, I am trying to configure ePBR on NCS540 (iosxr). When I try to attach the classes map "cm-providerz-tenanta", to the policy-map type pbr "pm-providerz-clients", I get an error. The command "show configuration failed" writes that cm-provider...
