Hi, All1) I need to do http-redirect for IPoE subscribers. Ideally I need to do http-redirect only for some users depending on reply recieved from Radius (accept/reject) or depending on some attribute from Radius. For test I add 15 rule in my control...
HiAny one knows hows to clear df bit in IOS-XR from interface.. we used to do it in IOS as follows:interface xxxx ip policy route-map CLEAR_DFroute-map clear-df-bit permit 10 match any set ip df 0We need to apply same for ASR running IOS-XR 4.2.1This...
Hello,What do you think if IOS-XR release 4.1.2 (CRS-8/S) is the good choice to use for management (SNMP)? I heard that IOS-XR 4.1.2 has some problems with SNMP. I want to integrate Prime IP NGN NMS with CRS. Maybe ISO-XR 4.3.1 or 4.3.2 can be bette...
Hi team,Is it possible to get nat statistics via SNMP wich contains in show cgn nat44 natXX stat command. We use IOS XR 4.3.1 and rancid every 1 and 4 minutes. But sometimes the cgn_ma process stayes in Blocked. Regards,Konstantin
Hi Team,I have few questions on ASR 9006Is ISSU supported on ASR 9006. Is it hitless or should we expect any packet loss. Also if you have any document or pointer that can walk me through the ISSU process on ASR 9006 , I will really appreciate it. (...
Hi,I'm trying iso 27001 penetrations test. But My asr 9006 failed every control. I'm haven't got a ssh software with asr 9006. How can apply login block-for command, min-password-lenght command, console access acl, time out etc for my asr 9006.
hello all, I have an RSA 9000 and want to configure NTP I get the following error:RP/0/RSP0/CPU0:InetGateway_4M(config)#show configuration failedTue Oct 1 18:45:45.094 utc!! SEMANTIC ERRORS: This configuration was rejected by!! the system due to sem...
Dear allIs it possible to upgrade from 4.3.1 to 4.3.2 with ISSU? Unfortunatly there is not a lot of documentation about the support of ISSU from one to another minor release.cheers,michel
Hello,we are getting a load of error logs on our ASR 9010 with IOS-XR 4.3.0 running. I've made a research on cisco.com and google but it's says only to contact TAC. It has multiple LC installed and errors are being seen on all except 0/0 and RSPs0/R...
DearsWas checking specs for new CRS-X and would like your feedback please regarding ASR9K vs CRS-X1- Beside CRS multishelf, why would someone prefer CRS-X over ASR9k ?ASR9K seems to be more interesting as it provides 440 G/slot however CRS-X provides...
Hi ,I have a question regarding CRS multichassis upgrades that when we upgarde the multichassis do we need to have code and all the SMU's and PIE in all the RP's or just in DSC RP's ( i.e ) Once DSC boots with the right code will it sync the new cod...
Hi,Can someone make me understand how to read the output of show process blocked. Everytime i use this command on XR platform and i got some of process are always there .. I need to understand what exactly we look in this output ?RP/0/7/CPU0:PE1#show...
HiDuring the IOS to XR upgrade on GSR router , i found a issue where "hw-module fast-ais-detect location" command failed to load/commit for multiple CHOC12 line cards .below error message observed in syslog:-LC/0/1/CPU0:Oct 13 08:14:35.301 : plim_fas...