The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi, I have a requirement to deploy an ISE appliance into a customer environment where the management network is separate from the data network. I understand that GEth0 is dedicated for management access to ISE so, I can assign an IP address to this...
I am trying to setup a NSS3000 Cisco NAS device. No matter how i set it up (Raid 0,1,5 jbod) and no matter how the share is configured, i cannot see it in windows!Im hoping a firmware upgrade (or downgrade) will get it working but i cannot find any...
Foro Ask Me Anything (del 18 al 27 de septiembre de 2024) Este foro está dedicado a las preguntas relacionadas con el webinar "Creando una Red Underlay para VXLAN aplicando las Mejores Prácticas Establecidas", del pasado jueves 18 de septiembre de 2...
Foro Ask Me Anything (del 12 al 20 de septiembre de 2024) Este foro está dedicado a las preguntas relacionadas con el webinar "Descubra las Novedades de SNA 7.5.0", del pasado jueves 12 de septiembre de 2024. Revisen la grabación, envíenos sus dudas...
How to avoid mac spoofing in MAB using Profiling Transitions and the use of Exception Actions We have ISE 3.3 Patch 3 deployed for one of our customer. For wired printer we are using MAB. For authentication and authorization, we are using the profil...
Hi, I have a scenario were i have to implement a solution which allows for dual ISP redundancy on spoke into dual hubs in a dmvpn environment. I have created two tunnel interfaces, both have tunnel source set at each respective physical interface...
in general, why asymmetric routing is not useful ?do it create slowness ?anyhow data is reaching to destination from source .Please share pros and cons of Asymmetric routing
Hello Everyone. I have cisco mx 700 which was installed by Government in our institution. It was previously registered to the old cucm. I have a new cucm 12.5. I want to re-register the mx700 to the new cucm but the touch panel is nowhere to be foun...
Hello all.I am looking for some clarification on the file requirements. In Control Hub, if I go to Location>Calling>Music on hold source I get this:If I go anywhere else to add a custom greeting through Calling>Features>Call Queue>Announcements I get...
Good afternoon everyone,Came across a curiosity as I was doing some network hardening for my campus network. I started blanketing access switch interfaces, spread across many vlans, with a configuration that included "ip verify source"~~ex.interface ...
I have been task to turn a immature network into something that looks more standardized. I wanted to create a Network Design with Collapse Distro & Core with a single WAN connection and two core/distro switches. Question 1.) For FHRP, what connection...
I have a question about HSRP and ACL configuration on Cisco 4506 and 4506E switches.Initially, without HSRP enabled, I configured the following ACL on the VLAN 55 interface:Extended IP access list vlan5510 permit ip any 192.168.104.32 0.0.0.1520 per...
Hi,we are using the Cisco ASR1001-X as core router on our ISP network. For the management of the CPE I set up a TR-069 ACS server. For testing purposes I configured the ACS URL manually on the CPE, which works fine.However I'd like our ASR to pass th...
Hi dear community,How can this happen ?Two dot1q headers on a captured MPLS frame going out from a Cisco ISR 1111-8P acting as a PE.Thanks in advance for your help !Regards,Jerems
I know this has been discussed, but my situation may be more unique. We were having issues with a 24 port POE 3850 not being able to power all necessary cameras (13 I believe). It has two 710w power supplies which is more than enough for this applica...