Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2133237members
1463922discussions

Featured Content

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

VTP issue

Hi All, i have an vtp server switch i want that my client switch get an vlan from server switch..but client switch unable to get an vlans from server...please find server switch trunk config:description "3850_Switch_VTP"switchport trunk encapsulation...

hamza-ali by • Spotlight
  • 82 Views
  • 1 replies
  • 0 Helpful votes

Retreiving Call data using JTAPI

Hi,I am working on retreiving call related data using JTAPI. I was able to get few fields using few classes in the JTAPI library. But I was unable to get the information such as Campaign name, Campaign Id, Call Started time, Disconnected Time, Durati...

Não Consigo emitir o Certificado - Badge

Olá! Podem me ajudar?Concluí o curso abaixo, cujo prazo vai até 31/12/2025, mas não consigo emitir a badge. Finalizei o último exame, com aprovação, em 28/12/2025. Meus dados pessoais também estão atualizados.Existe algum tempo de processamento para ...

monicabbotelho_0-1766934600137.png

FMC HA SECONDARY NODE IP CHANGE

I'm going to move my secondary FMC device to another physical location and i will change its ip address used in the HA configuration. so, i was planning to 1- break FMC HA  2- change FMC IP 3- configure HA again  what i expect that FTD will be manage...

Cisco catalyst 9200 Module Issue

We have Catalyst C9200L-24P-4X. I was swapping out an older switch for one of these. When I plugged a 1000base-SX SFP module in the system is reading it as a 10G LR module. We are running version 17.03.03. When doing a show inventory it does show the...

HA License on The Cisco 9800-L

Hello, Is the performance license mandatory to enable HA on the 9800-L? In the datasheet Cisco Catalyst 9800-L Wireless Controller Data Sheet - Cisco it says that: For High Availability deployments, Performance licenses must be brought on both contro...

HWIC-16A Configuration - Hardware fault?

I'm trying to configure a HWIC-16A as a terminal server without success. I can get a telnet session to connect, but I simply get a blank screen, no data appears to be sent or received over the serial line.The only similar post I could find was https:...

Cisco Catalyst 9115ax slow wifi

I'm looking for some help to pint me in the right direction.I have a Cisco Catalyst 9115e AX wireless access point running the embedded wireless LAN controller in my home lab.I have a SSID configured using WPA2/3 and dropping me into the correct VLAN...

by • Not applicable
  • 74 Views
  • 0 replies
  • 0 Helpful votes

VXLAN BGP EVPN Default Route

Hello all,  On Border Edges(DC01-BE001-6/7) am trying to advertise default route from GRT to MPBGP-EVPN but not able to do it properly with the following configruration. Thanks in advance for tips and correction **************************************...

uni1389_0-1766850713846.png
uni1389 by • Level 1
  • 787 Views
  • 11 replies
  • 0 Helpful votes

CBD network topology not right

Current SituationWe are encountering an issue with the network topology. The setup consists of 10 switches, all running firmware C1200-24P-4G and using the same model (C1200-24P-4G). These switches are organized into two clusters:Cluster 1: 7 switche...

GerwinH_0-1767001453665.png
Gerwin H by • Community Member
  • 110 Views
  • 0 replies
  • 0 Helpful votes
Load more