Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
[録画公開] 11/14 開催 Webex TAC Live Day 2
by Eri Mizuno -
Crypto Key RSA no longer supported
by thomas-moffat -
Un overview du VXLAN EVPN pour simplifier le concept
by Meddane -
QoS configuration for DMVPN hub
by rasmus.elmholt -
FMC Policy Export
by benolyndav -
Duplex issues when NXOS upgrade
by silverdoor12 -
POAP USB N9K
by georg-seidl -
VXLAN EVPN in Multisite
by JJYRR
Community Activity
Duplex issues when NXOS upgrade
My customer has N9K-C9348GC-FXP. Current OS is 7.0(3)I7(9), and willing to upgrade to 9.3(11). There are some ports that configured 100 speed, duplex full. When I verify this OS upgrade path by show install all command and show incompatibility, and t...
FMC Policy Export
HiThe Cisco Doc for the Policy import/export says the below, Does this mean just the FMCs should be on the same version and the FTD can be on a different version ?? (The importing and exporting appliances must be running the same version of the Firep...
Multi-Site VMM VMware Integration
Hello Community!I am looking for guidance regarding a Cisco ACI multi-site design and VMM integration. There is one vcenter which manages hosts in both sites but, it also has DRS clusters configured across the two sites (DRS_A contains hosts from bot...
Cisco 9330 gateway for ip phone vlan
Hello AllI have a cisco 3850 switch used for Distribute Layer.All Vlan and interface vlan are defined in this switch. Involved:vlan 80 name PC-vlanvlan 81 name IP-Phone vlaninterface vlan 80ip addr x.x.x.x x.x.x.xip helper address x.x.x.xIn layer 2: ...
Email notification when engineers starts and ends remote session
Dear sirs or madam,I am interested in a feature that I get an email when a Cisco TAC engineer starts a RADkit remote control session and when the session is ended. This way I know when remote access happened and I can verify the session logs instantl...
What's the real difference between point-to-point and multipoint int type
Hi All,Does any body know the real difference between point-to-point and multipoint interface type? I just know that when you use point-to-point in frame-relay etc, you can not connect to two peers (so in frame-relay, you can just config 1 virtual-ci...
ACI and NSX-T Intergrate
hi everyone, We are implementing a project and will integrate ACI with VMware NSX. I have a question: when integrating APIC with VMware NSX, is it necessary to first integrate with vCenter so that APIC automatically creates VDS, and then Integrate wi...
How monitor Cisco AP load?
Question posted by 1 customer i dunno how to ans.controller is C9800 wlc.is there any way or how to monitor an AP load and get notify before clients wifi connections performance start going south??
CSCwk48338 - AX AP doesn't accept clients
Man, there has to be another solution other than upgrading to iOS 17.12.3 .. We can't use that IOS because we still have 900 2702's on our controllers. We have 1500 9130's and 2800 3802's.I really wish Cisco would escalate this issue and get a patch...
TEAP Problem with Windows 10, ISE 3.2 with Patch 7 and EAP Chaining...
Hi all;Consider the following scenario:The client is configured as follows:The target computer and the user both have installed required certificates installed as you can see below:Now, the client machine is booted up and the following event is recor...
fabric with AVE or Vapic, how to check?
Hey Folks, I have an APIC cluster consists of 1 hardware APIC and 2 other Virtual APICs. I was looking for a command that shows if my two virtual APICs were installed as Vapic or as AVE (Cisco ACI Virtual Edge). I found the command `show fabric nodes...
Resolved! Unable to join C9130 AP to C9800-CL, certificate error
I get the following failure on the console of the AP when trying to join a C9800-CL WLC: [*08/18/2023 17:25:10.9392] CAPWAP State: Discovery [*08/18/2023 17:25:10.9417] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0) [*08/18/202...
LISP on Nexus 9k
Does the Nexus 95xx or 93xx support LISP? If not, is there planned support?
using ISAKMP through 3 router
im a newbie and student that currently still learning about the cisco, im trying to use ISAKMP to allow access between 3 different network for my assignment but i can only ping to the router instate of the end device, only the hq network can ping eac...
Cisco 9500 License
Hello,I have C9500 with Essential license and this license not support for stacking. Can I upgrade existing essential license applied on the box to Advantages to support virtual stacking?What SKU should I purchase?If i'm only upgrade the DNA license ...
