Hi community,I am trying to apply a DPP (Shared mode) for L3Out Interface Profile (containing only SVI), and encountered this fault.The physical interface used for SVI is of vPC, which doesn't have any other DPP types (Access Policies or EPG). APIC a...
Hello,Does anyone know why some policy groups create automatically overrides in Leaf Interface policies? I never add them manually. I alwayas configure Policy Groups. Recently I looked at Overrides and there were many individual policies created. Any...
Hi community, When I created an EPG-L3Out Contract (with L3Out having the mentioned config), I tried to show zoning-rule to see if the rules contained pcTag of 15 for L3Out EPG. The pcTag of EPG was 16399 As per the result of the command (on non-Bor...
Hello, We have an aci fabric in multipod with UCS and VMM integration.2 leaf are connected to 2 fabric interconnect via Vpc. What will happen when we reach the vlan limit(3960) on both leaf and fabric interconnect ?Do we need to buy other Fabric inte...
Hi community, What is the next-hop for the pervasive route? I found that it's a loopback on one of my Spines (but not on all 4). Is there a name for that loopback? (Like, there's a loopback for PTEP, a loopback for VTEP that is the same on vPC peer, ...
Hello Cisco Community, I have the following problem in a three Multi-Pod fabric:I can't reach the Hosts within the same EPG in Pod 3. Pod 1 & Pod 2 Hosts are reachable but not Pod 3. The two hosts are in the same subnet, epg and vlan:Host 1: 10.7.0.2...
Hi, I just started studying ACI, I understand that APIC pushes the policies to the fabric i.e SPINE/Leaf, does it also configure other components like firewall, LB etc?
Hi All, I am bringing up fabric with APIC version 4.1(1l). some of the leaf we received has older code and I would like to upgrade as stand alone switches/leaf before APIC can discover the leafs. Unfortunately My APIC is unable to discover these leaf...
Hi folks,I 've trying to solve a problem on our integration betwen ACI with VMM domain(version 5.5) and Vmware enviroment(ESXi 5.5). Some VM's lost conectivity after reboot and sometimes without no reason. To deal with it, I need to change the virtua...
Hey Guys,I'm looking at staging two ACI sites with multi-site orchestrator (MSO) at a single location. I only have access to one management network, so I will re-ip address the management interfaces of the 2nd DC ACI APICS to be in the new managemen...
Hi,what happens when the vlan limit (3960) on a leaf-pair is reached?Will it be possible to deploy new EPGs (on that leaf-pair)? If I am doing 1BD=1EPG will I be limited to 2000 BD per leaf as the scalability guide mentioned ? thanks
Does the logical node ID created during VPC setup need to be unique per fabric or per pod?example:leaf1201_leaf1202 nodeID 201 (pod1)leaf2201_leaf2202 nodeID 201 (pod2) appreciate your feedback!
Is there a special reason why the "Add Pod" Wizard with APIC 4.2 and newer creates multiple AAEPs (2 for Spines, 1 for L3out). Also different Access Port Policy Groups are used! Why? In all the documentation i found, I can't see a good explanation. ...
Hello there, I've a cluster of 3 apics, 2 are physical and I'm trying to add the 3rd as a virtual apic.The vapic seems correctly installed (I can ping the other 2 on the infra ip address) but it never showsin the controllers window. Is there a way t...
Hi All,I have a DHCP server reachable via shared l3out in common tenant default vrf. I configured dhcp provider in Fabric access policy.I have a user tenant called tenant-dev and vrf vrf-dev and bridge domain bd-100.In the bridge domain bd-100, i hav...
