Join the ACI conversation. Jump into this space for access to peers and industry experts. You’ll find the latest updates, helpful resources, and assistance when you need it.
Hi
Is it possible to connect an ESXi host to the ACI fabric via an intermediate switch when no AVS is being used?
Will it work if we allow the infra vlan / dynamic vlan pools on the links between the intermediate switch and the Leaf
thanks
Ambi
Has anyone had experience or know use cases where Nexus 9K (as Core and TOR/EOR switches) running in NX-OS are converted to ACI gradually? Is it even possible? I can't imagine the complication of breaking up vPC, etc..
Hi,
I have a question, one of the customer is asking for having control with in same EPG. For example if there is an EPG_FE with multiple VMs in it.How can we block access between these VMs under the same VLAN or EPG in ACI fabric?
Customer only hav...
Hi,
Can anyone please explain the actual functionality of UDP Header in VXLAN. Vxlan overlay is basically mac-in-udp, for l2 extension over l3, the concept is ok but I can not able to find out the actual role of UDP here.
Thanks!
Rajib
I have recently been working on an ACI ASA integration. Though it was a challenge to just get basic IP connectivity to the ASA, the real challenge is the function profiles. Once the APIC is managing the ASA, you lose the ability to configure the ASA ...
Dear All
I have the problem about APIC and ASAv (single vm) integration. I am using APIC 1.2(1i), I have successful import ASAv device package 1.2 into APIC, you can check on picture_01.png. Then I try to create L4-L7 device under Tenant, I put all r...
Switch was shipped with ACI mode, and I am trying to convert it back to standalone mode. I have the NX-OS image on the switch, however; the it will not boot into NX-OS from loader prompt. Can anyone assist?
All,
Our company recently purchased Cisco netscalers and we are in the process of migrating from cisco CSS to netscalers. The setup is as follows. We have two data centers, with a CSS device at each DC. The services are being load balanced between ...
Hello Experts,
I am trying to deploy an EPG on a leaf port where an N5K1 is connected. I have performed this task and i have deployed the same EPG on a leaf port where another layer-3 switch is connected. for both the ports i have used same encapsu...
Hello,
I'm able to play with e1/1 and access to the APIC controller from http://192.168.10.2 just fine. Somehow I'd like to connect the management interface (M) to our local network switch so I can access the APIC controller from my network and not ...
Building an ACI environment without the OOB-Mgmt interfaces connected. I have the APIC OOB mgmt interfaces connected for build, but eventually the switch they are connected to is going away and no capacity for leaf/spine interfaces.
Currently receiv...
Hi,I've just hooked up a leaf (9396PX) to the APIC appliance and did the initial setup of the APIC via the console; however, the APIC was unable to discover the leaf switch when I checked in the GUI under Fabric --> Inventory --> Fabric Membership.Co...
Hi Everyone,
I have N5K connected to leaf1 port 1/4 and leaf2 port 1/5 and i an trying to create a vPC.
while i am doing this, in the switch profile i selected two leafs and coming to interface selector, I am little confused here.
How do i select m...
Hello Guys,
I have 3 APIC controllers, one of them is up and running with 2 leafs and 2 spines. I was trying to work on the 2nd APIC and want it to join the cluster but somehow I think I might have crashed the 2nd APIC after rebooted it few times. ...
I am running APIC version 1.2(1i) and am trying to setup/create an L4-L7 device - a virtual F5 running 11.5.1. I have the latest F5 device package (version 1.2) installed as well. I've walked through all the steps a bunch of times but I keep gettin...
