Hi, what is stomped and not stomped? how it helps to troubleshoot CRC errors? Nexus-SW# show hardware internal bigsur port e1/21 | include ignore-case stompRX_PKT_CRC_NOT_STOMPED | 0RX_PKT_CRC_STOMPED | 0
Forum Posts
Resolved! Chassis Configuration for AFD Testing
I built a Nexus 9508 modular chassis with the following modules to test the AFD feature of the Nexus 9000 series but was unsuccessful:Fabric Module for Nexus 9508 chassis (Model: N9K-C9508-FM) – 4 unitsSupervisor Module for Nexus 9500 (Model: N9K-SUP...
hello We are running 4 Cisco devices. The composition is as follows 192.168.,100.97/30 -> 192.168.100.98/30(Standby) 192.168.100.101/30 -> 192.168.100.102/30(Active) The active and standby states are connected via mutual links. This morning I had...
Resolved! Cisco Nexus 3550-T SFP28 Compatibility
Hello everyone, I've been researching for over three days to confirm whether the Cisco Nexus 3550-T supports SFP28 modules, but I'm still uncertain. The specifications for the 3550-T clearly state that it supports speeds of 1/10/25G and features 48 S...
Resolved! N3550 SFP compatibility
Hello everyoneI have a question Is the Cisco Nexus 3550-T compatible with the SFP-25G-SR-S??I have searched in the Cisco matrix list, and it gives me that it only supported SFP 1G and 10G.
Hi We're currently about to start a HW refresh project to replace EoL N9Ks with new N9K hardware, so a like for like from the perspective of ports etc.This is for VXLAN leafs running OSPF, MPBGP and VPC. For the replacement we'd like to cause minima...
We are providing a file download service by colocating more than 120 file servers in a Internet Data Center (IDC). We have our switch connected to the IDC with 5x10Gbps lines. The disk read performance of the file server is fast enough, and each file...
Quick Q please:May DACs like SFP-H25G-CU5M be installed in any of 1st 48 slots of N9K-C93180YC-FX3H ? thanks
I have the below requirement. There are 3 companies say Company A, B,C.They will be having common Data center which means sharing the same network devices like Core and distribution layer switches.But logically they need to be separated. May be in fu...
Good morning cisco community, Is it possible on 7k series (running 8.4+) to disable the xml server? We require SSH of course for device management, so this would appear to be the underlying service replying to RPC with the XML rpc requests. On 9k the...
Hi, I found this command in the official Cisco configuration guide for vxlan. system vlan nve-overlay idFor scale environments, the VLAN IDs related to the VRF and Layer-3 VNI (L3VNI) must be reserved with the system vlan nve-overlay id command.Howe...
Hi., CRC errors seen on Leaf switch (interface to N3K) though QSFPs and fiber cables have been changed. See outputs from Leaf and N3K below: LEAF# show int eth1/21 <snip> TX 8657 output error N3K# sh int eth1/2 <snip> RX 8673 CRCI've try to check...
Folks; We usually see this design in networking, now my question is shall firewalls be dualhomed/ criss-crossed to both switches or just SW1 to uplink to FW1 (As shown), in later mode I see if the link fails between SW1 and FW1, firewall also need t...
We migrated some Dell servers with Broadcom BCM57454 Server NIC connected to 93108TC-FX to Nexus 93108TC-FX3P. Same configuration in NXOS is in place with NXOS version the same on both switches with 10.3.6M.Some 10 Gigabit Cat6a connections does not ...
Hello everyone, I need information about the forwarding rate (pps) of the Nexus 9364C-H1 device. I have searched through publicly available Cisco documents but couldn't find any results. Can anyone help me? Thank you very much!
