Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I believe the answer is no, but just want a sanity check:Is it possible to use MVA on a router where the PRI is controlled by MGCP by using an H323 dial-peer? This PRI has the DID I want to assign to MVA.
Dear All,I have one issue with 9951-Sip phone . i registerd some 9951 phone in CME.9.1 i also have service module (SM) with unity express 8.6.6 i went to unity express adding CME user there not showing SIP phone only i can see SCCP phones somebody ...
I have a small client with CME. They have two POTS lines that ring inbound as the 2nd and 3rd line on every phone in the building. They occasionally get priority calls from a specific external caller, all of which will originate from the same numbe...
Is IP communicator supported on Xenapp 6.5? I have it published and it seems to be working other than a few quirks. DIdn't know if there was any offical documentation regarding settings for this.Thanks
CUCM 7.01 Cisco 7970 phoneThe image file is a simple black and white file that I made in MS Paint with the word test on it. List.xml follows: <CiscoIPPhoneImageList><ImageItem Image=”TFTP:Desktops/320x212x12/tn-test.png”URL=”TFTP:D...
I am not able to make off-net calls from video phone regsitered to the CME. The remote offices are having call managers(CUCM 9.0) which are connected to the CME over a H.323 trunk. We are able to make calls to the video phone and also the phone is wo...
Can anyone tell me how exactly (steps) to configure CUCM 8.x to directly connect to SIP Gateway provider for Outbound calling over SIP trunk?(I am not using CUBE or CME)
Hi we have a cucm system (v8.X) with a sip trunk to a SIP pbx and H323 gateway to the PSTN. All works fine regarding calls in/out between PSTN and both the cucm and SIP PBX. However if we receive an external call to an extension on the SIP PBX and th...
I am working with a Call Manager Cluster running 8.6.2. I am testing outbound calls from the Call Manager to an Acme SBC and then out to our provider via SIP trunks. Our provider is sending a 180 RINGING message with SDP. There doesn't seem to be ...
My Company has about 350 7971 phones in productions right now. All are covered under Smartnet which will end July 31st. We have had numerous issues with the foot stand assembly breaking on them. It is not the footstand itself but the clip in the back...
Good evening guys,My new forum place, my first questions here.I come from a more traditional PBX world for the past several years administering Siemens HiPath4000 PBX (softswitch since latest version).Cisco UCM is quite a new concept for me, VoIP fro...
Hello All,I would like to connect a 2911 cisco router to sx2000 pbx using vwic2-2mft-t1/e1 card. The signaling protocol is used in sx2000 is DPNSS.The cisco router has E1 card, and the card is configured like this:!isdn switch-type primary-dpnss!cont...
I have a requirement for calls between Japan and Malaysia using a centralized CallManager MTP resource in Singapore. There is UCM servers in Japan and Singapore but not in Malaysia. Malaysia phones are using Singapore UCM as IP PBX.I have restriction...
Hi,We have implement IVR on our voice gateway 2921. It should work with incoming calls from PSTN through the SP's SIP-trunk. But the SP sends DTMF in band within g711. All calls to IVR are going through gateway to CCM and it forwards them back to gat...
Hi, We are facing problem with hearing ring back over PSTN. PSTN PRI----->MGCP GW. When user receives a inbound call over PSTN, the calling party hears busy tone, but the IP Phone/analog is not actually busy. This is happening with internal calls ...
