Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, I have the following dial peer configuration on an h323 gateway: dial-peer voice 1 pots translation-profile outgoing isdn_map destination-pattern 911$ progress_ind setup enable 3 progress_ind progress enable 8 incoming called-number . direct-in...
Hi, I've an issue with call forward all to external number on CME 8.6, when I make a call from PSTN number to an ephone-dn which has call-forward all to pstn number no problem but when I make a call from an internal number to the same ephone-dn the c...
How can you get the Cisco 7941G to use ring tone through headset when there are incoming calls?It works through the software version of it (Cisco IP communicator 7.0.6.0), but I cant get it to work with the hardware version.
Not sure if this is the right spot to ask this question?I attempted to upgrade a 7940 SIP phone to SCCP.I think I got my upgrade version wrong, the SIP image on it was "P0S3-06-3-00"I attempted to put SCCP 6.0.5 on it. I think the SCCP image was too ...
Customer wants to setup call forward to an external number, the external number is one extension of one company, not direct line. As my understand, we can dial the number "123456,2222" by mobile phone, the call is successful. 123456 is the compan...
Hi guys, for a very long time I've been trying to get my awesome phone (CP-7971G-GE) work with my asterisk pbx setup.As much as I've tried I've had no luck in getting the phone to register with my pbx, for some reason it just keeps claiming to be reg...
Hi all,I don't know if it's possible...I have two CME connected via ethernet. I have configured on both dial-peers to dial to the other CME extensions.I need to know when a person is on DnD state, without the need to stay in the same CME system.I am ...
Hi all,I find that once I pressed the redial button on my 7911 and 7975 phones, the last successful dialed number seem to show up 2 seconds later. This give the impression the redial is not work, but just slow.How do I reduce such timer? or can it be...
Hello everyoneCould you know which is the URL for the local directory on CME? I want that some phones in the CUCM cluster could access to this directory. I did not find anything on the cisco documentation.ThanksRegardsSanti
Hi,I have configured a SIP trunk on an UC500. Also, I added some phone numbers with their names.Now, I want to see the name of the caller on the display of the phones. This feature works with the PRI / BRI ports. With the SIP trunk it doesn't work.I ...
Hi Our customer have some C6941 ip phones, they want to program the buttons to be speed-dial button. How can they program by themself ?CME 8.6Thanks and RegardsLeung Che Man
Hi.I've connected vg224 to cucm 7.1.5 as mgcp gateway and discovered the problem:When I dial numbers contaning digits "2" or "6" I hear long silence and then busy signal. Today by using debug vpm signal command I discovered that this digits "2" and "...
Hi GuysPlease I need help..!!!When I perform a restart to the Publisher, the follow message appears: ..." Note, Forcing a Restart may leave your database in bad state "...I aborted the restart. What is the recommendation? .. I force a restart?..Can I...
Hello,I need some advice, we have Call Manager 4.1(3) and have around 800 sccp phones. Polycom SoundStation IP 7000 phones were purchased recently which are SIP.CAn these co exist in either Call Manager 4.1(3) or 8.x ? Would bes practice be either al...
Hi,We are currently running c2800nm-spservicesk9-mz.124-24.T4.bin" and using 7920, 7945 phones in a small setup.We are using 2 DID numbers for our sales lines that go to 2 hunt groups of which some people are members of both in an office.Is there a w...
