Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Could someone tell me where is the best place to globalise the called party from the perspective of a phone please?I am migrating to E164 and would like to know if this could be done at the device pool level using transformation patterns.e.g. If a us...
HiWe are trying to deploy a new Cisco 840 Wireless phone in our site.Anyone can you give me the steps for connecting the Cisco 840 phone and getting registered with the Call manager?regardsChandru
i have CP-8841 that i changed firmware to CP-8841-3PCC sip88xx.12-0-4MPP0101-205.loads with TFTP and now just show Enter activation code on phone.from https://192.168.199.102/admin/advanced i feel sip settings for my elastix but no any registration l...
Good Morning, So, we set up our CUCM and a majority of our phones have already registered with the numbers and names assigned to them, but there are a couple that are asking for an activation code or domain. None of the rest of them asked for it, but...
What is the license required to order Cisco CME running on an 8300 router and has 20 phones 7821, and 8841?
I'm attempting to modify the diversion header when calling one specific number. I want to modify the reason=unconditional to reason=deflection. I've made a single peer that I confirmed is matched, and assigned a sip profile to the outgoing peer whi...
Hi,I am getting the CDR error like below 10021 There are no matching recordsVerified under service parameters , cdr flag enabled True Please helpCUCM 11.5 Thanks
Hi, When a call is made to 8.XXX.XXXX x1145 from a video phone on the A end in this case an cisco 8865 with x2222. The call establishes with auto attendant on the B end and then presented to the end user at x1145. The B end user picks up the call and...
Hello, We are running CUCM v14. We have several call pickup groups which work fine if the phones are dialed directly. The phones are also in a line group and I want to configure a pickup group on the hunt pilot. The Hunt pilot, pickup group and direc...
CUCM 12.5, I have a Line Group with 3 users, top down then hunt pilot to VM. The RNA Reversion Timeout is set to 15 (per Cisco). One of my users (the first in the line group) sent me a message saying that incoming calls ring to her phone about 10 t...
Hi,We have a customer using HCS. As part of this we set up Expressway for them during the first lockdown for them to be able to use Jabber remotely for voice only (no IM&P). They use the same domain name internally and externally e.g. abc.com Another...
Hi all. In the screenshot I encountered a problem: immediately after turning it on, this appears. Has anyone else encountered this problem? It asks for a domain, username and password. The phone is completely new. There is a way to access the setting...
Our Forum Alert III Secondary Crash Net (SCN) is inoperable. I've heard the cisco cm could be configured to set up some devices to act as a ringdown, they called it a “Switch Box.” This would allow our Base Operations guys to have a work around from ...
Dear Sir i am new to 8851 ip phone , just need help for speed dial kem i do program speed dial entries into the device and when the phone is turned off the entries are lost is there is any advice why list is forgotten from the phone ? thanks
Hi Experts,I am sitting with an unique issue where my Auto Attendant works perfectly from inside the office, however it is not reachable from external calls.Connection ISP > SIP > CUBE > SIP > CUCMWhat I am seeing is as soon as I direct the call to C...
| User | Count |
|---|---|
| 7 | |
| 5 | |
| 4 | |
| 2 | |
| 1 |
