Has anyone used uplink interfaces on ME6524 to deliver xconnect (port based)? The configuration is supported but am not sure how the performance would be, have no test environment and hence cannot test. Suggestions would be much appreciated.Cheers
Dear All I'm trying to configure a csc scenario with 3 routers. Two routers at the edge presents the customer carriers while the 3rd router in between presents the backbone carrier. at the 3rd router ( the backbone carrier ) I configured vrf and assi...
HelloI just watched a strange thing - there is basic MPLS connection between PE1 <-> P <-> PE2 Router and I sniff outgoing messages from PE1 in this scenario. MPLS is enabled global with "ip cef" and also on all interfaces with "tag-switching ip" com...
I have setup a basic MPLS lab and am trying to get R1 and R11 to run RIP over the VRF PALMI am running OSPF inside and BGP between PE1 and PE2 I believe why R1 cannot ping R11 is that routes are not being passed between BGP because of the same AS?PE1...
HiI could help with the configuration of VPLS in the ME3750 because I find the settingsfor that computer and does not appear, or I might say if it is used for the 7600 router?
Hi all experts. Can someone explain me what is the meaning of aggregate when i do show mpls forwarding table. I tried searching here but it seems its meaning changes in different contexts. Like in mpls vpn, it means that this packet is for a VRF and ...
Hi all experts.If an ISP has a customer with 200 branches, and that customer wants all his branches to be provided layer 2 connectivity, means it wants a full mesh at layer 2 just like ethernet, so that there is no need for Tunnels and the client is ...
We have layer2 AToM working in our lab:CE-2941--to--PE-2811--------PE-3825--to--CE-2941question is:how does one configure one point-to-point PE layer2 tunnel that does not require the same VLAN tagging for the CE's VLAN, or different CE non-tagged VL...
Hi my problem is DR flapping basically DR changes from one PE to another, in my current environment I have about 8 PE so recently I see this log messages. This is effecting muticast traffic. Jun 14 09:01:38.758 MY: %PIM-5-NBRCHG: neighbor 10.0.32.36...
Hi All, I am working with an MPLS VPN in a Hub and Spoke fashion but hindered by a configuration on the HUB PE.All the configuration at the three sites are well understood, with the exception of a config on the HUB PE, which configures a vrf...
Hello,I have a Problem with one PE using Cisco 7206VXR (NPE-G2), The PE only reboot automatically, The following log in PE during and after reboot, Whatwhat causes this problem occurs ? We already replace device the PE using the same type of router b...
Hello,I have a problem with EoMPLS when i'm trying to config the tunnel between 2 PE ciscoThe schema is simpleCE1 - (gi3/12) PE1 --- (cloud MPLS ) --- PE2 (gi 3/8) - CE2PE1 : 6504 IOS s72033-advipservicesk9_wan-vz.122-33.SXI4.binPE2 : 7604 IOS c7600s...
I am thinking I would need a couple of VWIC2-2MFT-T1/E1's?I have two routers where I need to purchase some sort of T1 module that can terminate a connection for MPLS. All things being equal I guess I’d like to install a module that can support two...
Hi All,I am looking for which Cisco router models support MPLS in a small scale MPLS topology. I determined that a C2821 or C3825/C3845 with either a NM-16ESW or NMD-36ESW will support at both the MPLS-VPN PE and P. But when I look at the C2921 and i...
hi,as subject above, anyway sample config to configure MPLS IPV6 on cisco 3750ME?as i search in the net, they mentioned about 'vrf definition' i cant find it in my 3750ME..is there any IOS for this?Thanks.Lee