Hi,We configured cisco network assistant and added our switches. We can see the neighbor switches from cdp but in network assistant most of them do not show the neigbhor switches. What can be the problem?Thanks.
Hi,We configured cisco network assistant and added our switches. We can see the neighbor switches from cdp but in network assistant most of them do not show the neigbhor switches. What can be the problem?Thanks.
Hello community,I am trying to distribute new software to our infrastructure. Even though I have selected a large number of routers to deploy the image, the software download proceeds in bulks of 5. Is there any way to change this value, so that Prim...
I don't quite understand the different images and files associated with upgrading the Firepower chassis manager.I am trying to upgrade to v 2.6.1x but I see four different files.There is a fxos-k9-kickstart, fxos-k9-manager, fxos-k9-system and fxos-k...
Hello,Is there anyone using Cisco Prime Infrastructure to audit baseline config compliance of network devices?I was googling about this subject and I could not find instructions on doing that, except by creating a big list of compliance policies for ...
Hi all, I've been trying to find the OID for the above for the past few days without success. Just wondering if anybody can point me to the right place/provide me with the OID? Thanks
Hello Folks I'm trying to find out which devices support IPFIX or TWAMP?If anyone has got a hardware matrix for these features then it would be greatly appreciated.
Hello FolksI'm trying to find out NetFlow is supported on Cisco 800 series routers that is using VRFs. I know NetFlow works without VRFs but not sure if can be done on a per VRF bases. Any help appreciated. Thank you.
In PI3.1 there is topology layout scheme : Orthogonal.Now i need to upgrade to 3.7. Can you check if that type of layout is present in it? P.S. I tried 3.4 and there is not.
Hello, i use the Prime Infrastructure Features & Technologies « Cli Templates ». I want disable the Power Ethernet on each interface where the command "switchport voice vlan" is present.With this Cli content i put the command on all interface but i n...
After upgrade to Prime infra 3.7 from 3.3 several maps are missing AP placements. WLCs been resynced after upgrade. Any ideas?
Hi All,I have Linksys N300 Wi-Fi router. i want to setup this in my small business local network.My local network infrastructure is:ISP>CISCO1841 Router>unmanaged switch>end usermy all end user use static IP to access internet.IP: 10.91.149.XSM: 255....
If i have the range of 172.16.3.0 /25And i have 172.16.3 254Why 172.16.3 254 not in the range of 172.16.3.0 /25And to what ip should i change the 172.16.3 254 so it would be in the rangeof = 172.16.3.0 /25Thanks for the halp (:
Good day everyone - i am seeing a lot of traffic related to akamai in netflow using up a lot of our bandwidth, the issue here is that i can identify the DNS of the service being provided - exp - a23-15-4-33.deploy.static.akamaitechnologies.com how do...
Hello communityWe keep getting these messages on our Nexus 7710 (all VDCs).pam_aaa:Authentication failed from PI_address - dcos_sshd These occur at random intervals and I don't seem to be able to figure out what function of Prime Infrastructure is re...
Hi all, As part of a research project, I need to securely download data from a web-based server to a gateway computer. From the gateway computer, the data needs to flow to a local network. I need to implement the above configuration with the followin...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-16-2024 04:45 AM | ||
04-16-2024 01:33 AM | ||
04-13-2024 12:00 PM | ||
04-11-2024 05:18 AM | ||
04-08-2024 08:39 AM |
User | Count |
---|---|
7 | |
2 | |
1 | |
1 | |
1 |