Hi everyone, I have topology like this: i want configure pbr on nexus, the scenario is if source 10.10.10.0 to 192.168.32.0, the first next hop choose via RTR-1 (1.1.1.0/30), if link to RTR-1 down, the secondary next hop is via R...
Forum Posts
Hi, I have lots of customers using SNMPv3 on their Cisco devices. I do have backup copies of their startup/running config files and am required to restored their devices if there are any hardware failures. I do understand that configured snmpv3 use...
Resolved! Except script banner error
Hello, i would like to use except script to automated the configuration of my switches . I tried it's work well but i have somes errors with the banner. Here is my script : but i have this errors : what's the problems ? Thanks
We have a few 4507's running which we're trying to monitor with SNMP. The OID 1.3.6.1.4.1.9.9.109.1.1.1.1.7.X should get me the CPU-usage in the last minute according the MIB. Now if I try to use snmpget I get the following error: snmpget -v2c -c pub...
Hi, can some-one please assist with suggestions for an EEM script to monitor the Cellular RSSI which the results can be checked by the script for IP routes to be removed and added for traffic to be sent to the same end-point for an IPsec tunnel but t...
Any help is greatly appreciated. Here's what I'm trying to do. See attached for PDF diagram. Overall, I'm running ip sla to check for latency above 150ms or a ping timeout. If that happens, I want to set the interface to passive in the EIGRP configur...
Hi guys, i want to know what exactly detail about licensing. I have a switch 4500, but the licensing not active and permanent (enterprise service). So, i configure two command: 1. license boot level entservices 2. license right-to-use activate ents...
Hi I have nearly 200 switches in my network with different vendor (Cisco,Junos, Allied Telesis,Dell) and nearly 3000 user using the resource.So i want to check which PC is connected which switch and port of that switch.So Is there any possible to c...
Hi there, I need to Archive received SMS on a CISCO 819G-4G-GA-K9 (Version 15.5(3)M4a) to a FTP server. I entered to configuration lines: ip ftp source-interface Vlan1 controller Cellular 0 lte sms archive path ftp://user:password@10.1.1.1/SMS-LTE...
Dear expert, i need to add port security in my access switches when the interface's description has AV/PV/UV/VV description AVxx:06afasf or description PVxx:05asfasf or description UVxx:06afasfas or description VVxx:0afasfasgasgfasgbelow is my t...
Hi, I have a Nexus Switch with WAN Links in different VRFs and corresponding LANs in respective VRF. I need to configure a ERSPAN with one of the WAN links as source and ERSPAN destination connected to same switch. My ERSPAN config on switch is as ...
Hello, My customer purchased Cisco Prime infra 3.1 for WLC and MSE monitoring. They have Hyper-v 2012 environment. as per datasheet, it is mentioned Windows 2016 server & Hyper-V 2016 server. https://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infra...
Hello, How to show the dashlet that I have created on the monitoring policies. i already followed the cisco document but no success. http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/3-1/user/guide/pi_ug/view-dash.html#41391 My goal...
Hi, I keep getting cisco prime alarms in the format Device IP address authentication failed for request from IP address. Please do you know how I can resolve this issue in Cisco Prime. Many thanks in advance
We are facing high CPU spikes due SNMP process. We are getting many SNMP drops from the servers. Please check and do the needful. COMUMA67SW_FORT1F_AC3750_01#show snmpChassis: FOC1512Z1LALocation: Fort house415520 SNMP packets input 0 Bad SNMP v...
